28276
23
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
3-4
3. Select 6. Int Reject.
4. Select level desired by operating the
omnipad.
5. Press the [ACQ/ENTER] key.
6. Press the [MENU] key to close the menu.
IR1, IR2 or IR3 appears at the bottom right
corner on the display when the interference
rejection circuit is turned on.
3.6 Selecting Pulsewidth
Pulsewidth is the time in microseconds nec-
essary to transmit a single radar pulse. The
longer the pulsewidth the greater the direc-
tion range capability, however range accu-
racy and range resolution are reduced.
Pulsewidth can be selected to short or long
on the 1.5 and 3 nautical mile ranges.
1. Press the [MENU] key.
2. Select OTHER MENU and press the
[ACQ/ENTER] key.
3. Select 7. Pulselength.
4. Select Short or Long by pressing the
omnipad.
5. Press the [ACQ/ENTER] key to select.
6. Press the [MENU] key to close the menu.
3.7 Guard Alarm
The guard alarm allows the operator to set
the desired range and bearing for a guard
zone. When ships, islands, landmasses, etc.
violate the guard zone an audible alarm
sounds and the offending target blinks to call
the operators attention.
The guard alarm is a useful anti-collision
aid, but does not relieve the operator of the
responsibility to also keep a visual lookout
for possible collision situations. The alarm
should never be used as the sole means
for detecting possible collision situations.
CAUTION
Selection of guard zone type
The guard alarm can be set to sound when a
target either enters or exits the guard zone.
You can select which type of guard alarm you
want through the menu.
In alarm
The alarm sounds on targets entering the
guard zone. G (IN) appears at the top right-
hand corner when the In alarm is selected.
Out alarm
The alarm sounds on targets exiting the guard
zone. G (OUT) appears at the top right-hand
corner when the Out alarm is selected.
IN ALARM
OUT ALARM
Guard
zone
Dashed line:
no alarm
Figure 3-7 In and Out alarms
Selecting guard zone type
1. Press the [MENU] key, select OTHERS
MENU, and then press the [ACQ/EN-
TER] key.
2. Select 17. Guard Mode and In (alarm
on target entering zone) or Out (alarm
on target exiting zone) by operating the
omnipad.
3. Press the [ACQ/ENTER] key.
4. Press the [MENU] key to close the menu.
Setting a guard zone
1. Mentally create the guard zone you want
to set. Figure 3-8 shows an example.
2. Operate the omnipad to set the cursor on
point A (or B). Press the [GUARD] key.
*G (IN) or *G (OUT), with asterisk blink-
ing, appears at the top right-hand corner
of the display. See Figure 3-8 (2). (The
asterisk indicates the guard zone is par-
tially set.)
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno 1932MK2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno 1932MK2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info