28276
17
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
2-6
2.12 Measuring the Bearing
There are two ways to measure the bearing
to a target: by the cursor, and by the EBL
(Electronic Bearing Line).
Measuring bearing by cursor
Operate the omnipad to bisect the target with
the cursor intersection. The bearing to the
target appears at the bottom of the display.
Measuring bearing by EBL
1. Press the [EBL/VRM SELECT] key to cir-
cumscribe an EBL readout (at the bottom
left-hand corner). Each press of the key
selects the readout of EBL1, EBL2, VRM1
or VRM2 in that order.
2. Press the [EBL/VRM CONTROL] key to
enable control of the EBL by the omnipad.
3. Operate the omnipad to bisect the target
with the EBL. The omnipad must be op-
erated within five seconds after pressing
the [EBL/VRM CONTROL] key, otherwise
the EBL cannot be operated.
4. Check the EBL readout at the bottom left-
hand corner of the display to find the bear-
ing to the target.
5. To anchor the EBL, press the [EBL/VRM
CONTROL] key.
To erase the EBL and its readout, press and
hold down the [EBL/VRM CONTROL] key
about two seconds.
6.0 NM
2.0
EBL1 bearing
EBL1 bearing
40.0° R
135.0° R
EBL
EBL1
EBL2
Target
Cursor
Cursor
bearing
40.0°R 4.0 NM
Figure 2-8 How to measure bearing by EBL
and cursor
Note: The bearing readout for the EBL andthe
cursor can be displayed in relatiive or true
bearing (true bearing requires heading sen-
sor input). For north up and course up dis-
play modes the bearing reference is always
true. For details see the next chapter.
Tips for measuring bearing
¡ Bearing measurements of smaller targets
are more accurate; the center of larger
target pips is not as easily identified.
¡ Bearings of stationary or slower moving
targets are more accurate than bearings
of faster moving targets.
¡ To minimize bearing errors keep echoes
in the outer half of the picture by chang-
ing the range scale; angular difference
becomes difficult to resolve as a target
approaches the center of the display.
2.13 Using the Offset EBL
The offset EBL provides two functions: pre-
dict collision course of a radar target and mea-
sure the range and the bearing between two
targets.
Predicting collision course
1. Operate the omnipad to place the cursor
on the center of the target.
2. Press the [EBL/VRM SELECT] key to
choose the EBL1 readout, and then press
the [EBL/VRM CONTROL] key.
3. Press the [MENU] key, select EBL OFF-
SET from the menu, and then press the
[ACQ/ENTER] key.
4. Press the [EBL/VRM CONTROL] key.
5. Oparate the omnipad so EBL1 passes
through the center of the target.
If the target tracks along the EBL towards the
center of the display (your vessels position),
the target may be on a collision course.
To cancel the offset EBL, select EBL OFF-
SET from the menu and press the [ACQ/
ENTER] key.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno 1932MK2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno 1932MK2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info