28270
40
Verklein
Vergroot
Pagina terug
1/63
Pagina verder
29
Final preparation
1. Place the antenna housing cover on the
housing. Loosely fasten the four fixing
bolts on the cover.
Fixing
holes
Scanner housing
cover
Pinning
hole
Figure 6-15 Fastening the antenna
housing cover
2. Apply grease to the two slot pins. Using a
wooden hammer to prevent damage to
paint, insert slotted pins into the pinning
holes until the pin head is flush with the
scanner housing surface.
Radiator
bracket
Ship’s
bow
Slotted pin
Face in
stern direction.
Figure 6-16 How to insert slot pins
3. Now is the time to fix the radiator to the
radiator bracket. Apply anticorrosive seal-
ant (silicone sealant) to hatched areas, to
prevent corrosion. See the figure below.
Apply silicone sealant into threaded holes
on the scanner radiator. Remove the cap
on the radiator bracket and orient the ra-
diator bracket as shown in Figure 6-13.
Apply grease to the O-ring and set it to the
center of the radiator bracket. Coat the ra-
diator fixing bolts with silicone sealant.
Fasten the radiator to the radiator bracket
with the FURUNO logo on the radiator fac-
ing ship’s bow.
Waveguide
Groove
Note: Apply anticorrosive
sealant to hatched areas,
antenna radiator bottom
view of XN8 type radiator.
Figure 6-17 How to coat radiator with
silicone sealant for XN8 type radiator
Flat washer
Spring washer
Hex head bolt
(M8 x 30)
Radiator bracket
Coat bolts with
silicone sealant.
Scanner
radiator
O-ring
Apply silicone sealant
into threaded holes.
Note: Apply anticorrosive sealant
to hached areas, antenna bracket
for XN12A type radiator.
Figure 6-18 Fastening the radiator to the
radiator bracket
4. Open the antenna housing cover and fix the
stay as shown in Figure 6-19.
5. One end of the cable with 15-, 9- and 7-
way plugs has already been connected to
RTB-9100 inside the scanner housing.
Mate the 15- and 9-way plugs with jacks
J812 and J811 on the transceiver module,
respectively. Connect the 7-way plug to
jack J701 on the MP Board. Secure the
cable between RTB-9100 and J701 with the
cable tie as shown in Figure 6-19.
Cable
tie
J812
J811
Stay
MP Board
Fasten ground
wire here.
Figure 6-19 Antenna unit, cover opened
6. Fasten the ground wire (black) of the sig-
nal cable to the chassis as shown in Figure
6-19.
7. Loosely fasten the antenna housing cover.
You will tighten the fixing bolts after con-
firming magnetron heater voltage.
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno 1932 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno 1932 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Furuno 1932

Furuno 1932 Gebruiksaanwijzing - Espanôl - 53 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info