596216
7
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
1
1. INSTALLATION
1.1 Antenna Unit
Installation
Mounting considerations
When selecting a mounting location for the
antenna unit keep in mind the following points.
Install the antenna unit on the hardtop, radar
arch or on a mast on an appropriate platform.
(For sailboats, a mounting bracket is
optionally available.) It should be placed
where there is a good all-round view with, as
far as possible, no part of the ship’s
superstructure or rigging intercepting the
scanning beam. Any obstruction will cause
shadow and blind sectors. A mast, for
instance, with a diameter considerably less
than the width of the antenna unit, will cause
only a small blind sector. However, a
horizontal spreader or crosstrees in the same
horizontal plane would be a much more
serious obstruction; place the antenna unit
well above or below it.
Antenna unit mounted
on top of wheelhouse
Antenna unit
fixed to mast
Figure 1 Typical ant
e
nna unit placement on
powerboat and sailboat
In order to minimize the chance of picking up
electrical interference, avoid where possible
routing the antenna cable near other
electrical equipment onboard. Also avoid
running the cable in parallel with power
cables.
The compass safe distance of 1.25 meters
(standard compass) and 0.95 meters
(steering compass) should be observed to
prevent deviation of the magnetic compass.
Mounting on a platform
1. Remove mounting hardware at the bottom
of the antenna unit; four each of hex bolts
(M10X20), spring washers and flat washers.
Save mounting hardware to use it to fix the
antenna unit to the mounting platform later
on.
Flat washer
Spring washer
Hex bolt (M10 x 20)
Screws
one screw on other side
Figure 2 Antenna unit, showing location of
mounting hardware
2. Unfasten three screws to remove the cover.
3. Construct a platform (wood, steel, or
aluminum) of 510 mm in thickness whose
dimensions are as shown in Figure 4.
Fasten the platform to the mounting
location. Next, position the base so the
cable entrance faces the stern direction and
the vent tube is extending downward
through the hole for the vent tube.
Note:
When drilling holes in the platform, be
sure they are parallel with the fore and aft
line.
160
210
130
160
210
MOUNTING
PLATFORM
(Local Supply)
Hole for Vent Tube
(φ20mm)
Fixing Hole
(φ11mm)
Bow
Figure 3 Dimensions of antenna platform
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno 1622 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno 1622 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Furuno 1622

Furuno 1622 Gebruiksaanwijzing - English - 35 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info