560830
6
Verklein
Vergroot
Pagina terug
1/71
Pagina verder
6
3. Press the tamper switch. The indicators in the front lens flash
several times and then continue to flash alternately every 5 seconds
to indicate that the siren is operational.
4. Remove the protective film from the solar panel.
Caution:
Make sure that the solar panel receives sufficient light to maintain
the battery charge.
5. a) If switch 5 is set to ON (siren), the siren will operate without
control panel (single zone).
b) If switch 5 is set to OFF (control panel), the siren will operate
with control panel. For linking the siren to the control panel, refer
to the Installation and Operation Manual for the alarm system and
to the Quick Installation Guide for the siren.
5.3 Adding a new remote control or remote keypad to the siren
If you set up the siren without separate control panel (single zone) for the first time, you must link the siren to a remote keypad
or a remote control before adding other devices. The ID code of the remote control or the remote keypad must be learned by
the siren. The siren can learn up to 6 remote controls or remote keypads.
During setup, the siren will power up in service mode, ready to learn a new remote control or remote keypad. If the siren is in
operating mode, refer to the section “Service mode / Operating mode” to switch to service mode.
Remote control
Remote keypad
1
Press and hold the learn button on the siren for 5 seconds to enter learn mode.
The siren emits one short beep. The indicators in the front lens and the learn indicator flash slowly.
2
Program the ID code:
Press the button.
Enter the 4-digit ID code. Press the button.
The siren emits two short beeps. The indicators in the front lens and the learn indicator flash quickly.
Note:
If the remote control or the remote keypad has already been linked or if the maximum number of 6 remote controls
or remote keypads are linked, the siren will emit one short beep and exit learn mode. The indicators in the front
lens and the learn indicator will go off.
3
Confirm the ID code:
Press the button within 15 seconds.
Enter the 4-digit ID code and press the button
within 15 seconds.
The siren emits three short beeps. The indicators in the front lens and the learn indicator come on for 3 seconds and
go off. The siren returns to service mode.
Note:
If the confirmation signal is not received within 15 seconds, the siren will emit one short beep and exit learn mode.
The indicators in the front lens and the learn indicator will go off.
1. Install the battery cover.
2. Install the screws.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Friedland FGGA04 Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Friedland FGGA04 Series in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info