Guarantee and Guarantee Policy
If any part is found to be defective due to faulty
manufacture within the guarantee period, Electrolux
Outdoor Products, through its Authorised Service
Repairers will effect the repair or replacement to the
customer free of charge providing:
(a) Where the machine is used commercially the
guarantee is 90 days.
(b) The fault is reported directly to the Authorised
Repairer.
(c) Proof of purchase is provided.
(d) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(e) The failure has not occurred through fair wear and
tear.
(f) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Electrolux Outdoor Products.
(g) The machine has not been used for hire.
(h) The machine is owned by the original purchaser.
(i) The product has not been used outside of the
country in which it was purchased.
* This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore
it is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged cutting lines and
cutting disc.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and
recommendations contained in this Operator's
Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject
to a valid warranty claim: Cutting lines, cutting disc,
belts, cables, recoil ropes, filters.
* Caution!
Electrolux Outdoor Products does not accept liability
under the warranty for defects caused in whole or
part, directly or indirectly by the fitting of
replacement parts or additional parts that are not
either manufactured or approved by Electrolux
Outdoor Products, or by the machine having been
modified in any way.
Environmental Information
Electrolux Outdoor Products are manufactured under an
Environmental Management System (ISO 14001)
using, where practical, components manufactured in the
most environmentally responsible manner, according to
company procedures, and with the potential for
recycling at the end of the products’ life.
• Packaging is recyclable and plastic components
have been labelled (where practical) for categorised
recycling.
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
DISPOSAL OF FUELS AND LUBRICA
TING OILS
• Wear protective clothing when handling any fuels
and lubricants.
• Avoid contact with skin.
• Remove petrol and engine oil before transporting
the product.
• Contact your local authority for information of your
nearest Recycling/Disposal Station.
• Do NOT dispose of used fuels/oils with
household waste
• Do NOT dispose of used fuels/oils to water.
• Waste fuels/oils are harmful, but can be
recycled and should be disposed of through the
recognised facilities.
• Do NOT incinerate
Service Recommendations
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a
professional application.
Fault Finding
Engine Will Not Start
1. Ensure that the start/stop switch is in the start
position.
2. Check that there is sufficient fuel of the correct mix
in the fuel tank.
3. The engine may have flooded. Remove and dry the
spark plug.
4. Fuel mixture may be incorrect or stale - if so -
replace with fresh mixture.
5. Check that the disc bolt is tight. A loose disc bolt
could cause difficult starting.
6. If the engine will still not start - disconnect the
spark plug lead and consult your local approved
Service Centre/Dealer.
Poor Flotation or Lack of Power
1. Disconnect the spark plug lead.
2. Clean the underside of the hood, the air filter, the
fan, around the engine and the air intakes.
3. Fuel mixture may be incorrect or stale - if so -
replace with fresh mixture.
4. If poor flotation or lack of power persists -
disconnect the spark plug lead and consult your
local approved Service Centre/Dealer.
Excessive Vibration
1. Disconnect the spark plug lead.
2. Check that the cutting disc and cutting lines are
correctly fitted. See ' Cutting Line and Height
Adjustment'.
3. If the cutting lines or cutting disc are damaged or
worn replace them with a new ones.
4. If vibration persists - do not use - disconnect
the spark plug lead and consult your local
approved Service Centre/Dealer.
ENGLISH - 4
