Handleiding Flymo Contour PowerPlus (pagina 3 van 9) (Engels)

631002

Verklein

Vergroot

Pagina terug

1/9

Pagina verder

3. Do not use the trimmer if the electric cables are

damaged or worn.

4. Immediately disconnect from the mains electricity sup-

ply if the cable is cut, or the insulation is damaged.

Do not touch the electric cable until the electrical sup-

ply has been disconnected. Do not repair a cut or

damaged cable. Replace it with a new one.

5. Your extension cable must be uncoiled, coiled cables

can overheat and reduce the efficiency of your trimmer.

6. Keep the cable clear of the cutting area and obsta-

cles at all times.

7. Do not pull cable around sharp objects.

8. Always switch off at the mains before disconnecting

any plug, cable connector or extension cable.

9. Never pull on the cable to disconnect any of the plugs.

10. Switch off, remove plug from mains and examine

electric supply cable for damage or ageing befor

winding cable for storage. Do not repair a damaged

cable, replace it with a new one. Use only Flymo

replacement cable.

11. Always wind cable carefully, avoiding kinking.

12. Use only on AC mains supply voltage shown on the

product rating label.

13. Flymo trimmers are double insulated to EN60335.

Under no circumstance should an earth be connect-

ed to any part of the trimmer.

Preparation

1. While using your product always wear substantial

footwear and long trousers.

2. Before using the machine and after any impact, check

for signs of wear or damage and repair as necessary.

3. Inspect the area to be cut before each use. Remove

all objects such as stones, broken glass, nails, wire,

string etc, which can be thrown or become entan-

gled in the trimmer head.

4. Check that the cutting head is fitted correctly.

Use

AVOID ACCIDENTAL STARTING. REMOVE PLUG

FROM MAINS AND KEEP FEET AWAY FROM THE

SWITCH LEVER WHEN:- CLEANING AROUND THE

INSIDE OF THE SAFETY GUARD, REMOVING OR

REFITTING SPOOL CAP, MANUALLY FEEDING OR

REPLACING NYLON LINE.

1. Use the trimmer only in daylight or good artificial light.

2. Avoid operating your trimmer in wet grass, where feasible.

3. Take care in wet grass, you may lose your footing.

4. On slopes, be extra careful of your footing and wear

non-slip footwear.

5. Do not walk backwards when trimming, you could

trip. Walk never run.

6. Keep cutting head below waist level.

7. Switch off before pushing the trimmer over surfaces

other than grass.

8. Never operate the trimmer with damaged guards or

without guards in place.

9. Never fit metal cutting elements.

10. Keep hands and feet away from the cutting means at

all times and especially when switching on the motor.

11. Never pick up or carry a trimmer by the cable.

12. Do not lean over the trimmer guard - objects may

be thrown by the cutting line.

13. Remove the plug from the mains :

- before leaving the trimmer unattended for any period;

- before clearing a blockage;

- before checking, cleaning or working on the appliance;

- if you hit an object. Do not use your trimmer until

you are sure that the entire trimmer is in a safe

operating condition;

- if the trimmer starts to vibrate abnormally. Check

immediately. Excessive vibration can cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure the

trimmer is in safe working condition.

2. Replace worn or damaged parts for safety.

3. Only use the replacement cutting line specified for

this product.

4. Only use replacement parts and accessories recom-

mended by Husqvarna Outdoor Products.

5. To avoid the risk of injury keep fingers and hands clear

of the line cutter on the leading edge of the guard.

6. Inspect and maintain the trimmer regularly. Any

repairs must be carried out by an authorised repair-

er.

Cables

IMPORTANT

Use only 1.00mm

size cable up to 40 metres length

maximum.

Maximum rating:

1.00mm

size cable, 10 amps 250 volts AC.

THE CONTOUR POWER PLUS IS SUPPLIED

WITH AN ELECTRIC MAINS CABLE WIRED

DIRECTLY INTO THE PRODUCT.

1. Flymo Mains Cables and Extension Cables are

available from your local Approved Service Centre.

2. Do not wire an extension cable directly to your prod-

uct yourself. Please contact your local Approved

Service Centre for further information on the connec-

tors and kits available.

3. Only use extension cables specifically designed for

outdoor use.

CONNECTORS

Flymo connectors are suitable for use with 2 core cable

only. Under no circumstances should these connectors

be used for earthed products.

All Flymo connectors and cables are of splashproof

construction. They are not waterproof and must not be

left outside permanently nor should they be submerged

or immersed in water. Do not let cable lay or trail

through pools of water or splashed with water from

hose pipes.

MAINS PLUG REPLACEMENT

• If the plug supplied is cut off it should be

destroyed. There is an electric shock hazard if a

cut off plug is inserted into a 13 amp socket.

1. No earth required. Flymo products are double

insulated to EN60335 and under no circumstances

should an earth be connected to any part of the

product.

2. Ensure the mains voltage suits your product.

3. IMPORTANT!

The wires in the mains lead are coloured in accordance

with the following code:

BLUE - NEUTRAL

BROWN - LIVE

The wire which is coloured BLUE must be connected to

the Terminal which is marked with the letter ‘N’ or

coloured BLACK. The wire which is coloured BROWN

must be connected to the Terminal which is marked with

the letter ‘L’ or coloured RED.

4. It is important that the outer sheath is clamped cor-

rectly into the 3-pin plug.

5. If in doubt consult your local Service Repairer or

qualified electrician before the machine is used.

6. A 5 Amp fuse must be fitted to the Mains Plug.

7. The normal plug fuse and household fuse only pro-

tect the electrical equipment and are not a safe-

guard against electrocution.

If your product is hard wired i.e. non-detachable

mains electric cable, a conversion kit and exten-

sion cable is available from all Approved Service

Centres which can be found in your local Yellow

Pages.

Assembly of Switch Handle to Tube (A1)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the switch handle.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Assembly of T

rimmer Head to Tube (A2)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the trimmer head.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Safety Guar

d Assembly (B1) & (B2)

1. Locate the safety guard over the cutting head.

Ensure the nylon line is fed through the hole in the

safety guard as illustrated in fig B1.

2. Push into location and turn safety guard in the direc-

tion illustrated in Fig B2, until a click is heard and the

safety guard is securely locked in position.

• ENSURE THE SAFETY GUARD IS SECURELY IN

PLACE BY ATTEMPTING TO TWIST GUARD.

Wheel Assembly (C1)

& (C2)

1. Fix the 2 halves of the wheel together as illustrated in

fig C1.

2. Attach the wheel to the trimmer making sure that it is

located into the groove on the trimmer head (C2).

3. Clip the wheel together on the other side, making

sure it is secure.

4. The wheel should turn freely.

Steady Handle Assembly (D)

1. Depress the two buttons on the sides of the switch

handle.

2. Locate the steady handle over the buttons and

release the buttons.

3. Adjust the steady handle to the most comfortable

operating position by depressing the buttons and

moving the handle.

Height Adjustment (E)

1. Turn height adjuster (E1) in the direction indicated to

un-lock (E2).

2. Adjust the length of the tube to the most comfortable

operating position.

3. Turn height adjuster in the opposite direction to lock

(E3).

• ENSURE THAT THE TUBE IS FULLY SECURED.

Cable Restraint (F1) & (F2)

1. Form loop in mains cable and push the loop through

the slot as illustrated in picture (F1).

2. To secure, position loop over the hook and pull the

cable back through the slot as illustrated in picture

(F2).

Assembly Instructions

C1 C2

F1 F2

Double Auto Feed System

• WARNING

• The use of eye protection is recommended.

Do not lean over the trimmer whilst trimming or

edging, objects may be thrown by the cutting

line.

Do not allow cutting head to rest on the ground.

Do not overload your trimmer.

Overloading can be avoided by making sure the

motor speed does not drop unduly.

DISCONNECT FROM THE MAINS ELECTRICITY

SUPPLY BEFORE ATTEMPTING ANY MAINTE-

NANCE OR ADJUSTMENT.

• BEFORE USE

Make sure that both lines are fed out.

• Make sure motor is up to full speed before trim-

ming or edging.

How to trim

1. Hold as illustrated in Fig H.

2. To start, squeeze the switch lever.

3. Cut with nylon line at an angle using the tip. See Fig

4. Swing trimmer in and out of the cutting area taking

small cuts (K)

5. Line is fed out automatically every time the trimmer

head stops rotating and returns to operating speed.

• Extra line can be fed out manually as described in

Manual line feed

6. To stop your trimmer release the switch lever.

How to edge

1. To convert to edging mode, press button (L1) and

twist head (L2). An audible "click" will confirm that

the head is locked.

2. Hold as illustrated in Fig H.

3. To start, squeeze the switch lever.

4. Rest edger on wheel for extra stability and line up the

edge of the lawn with the two indicators on the guard

(M1). Edge in direction indicated in Fig M.

5. To stop your trimmer release the switch lever.

6. To return to trimming mode, press button and twist

head back the opposite way. An audible "click" will

confirm that the head is locked.

How to trim and edge

How the automatic line feed works (G)

1. When initially switching on the trimmer, a small length

of line is fed out.

2. A ‘clattering’ noise will be heard when the two nylon

lines hit the line cutter. DO NOT BE ALARMED this

is quite normal. After approximately 5 seconds the

line will be cut to the correct length and the noise will

reduce as the motor reaches full speed.

• Make sure the motor is up to full speed before

trimming or edging.

3. If the noise of the nylon line being cut cannot be

heard, more line will need to be fed out.

4. To feed more line, it is first necessary to to allow the

motor to stop completely, then re-start, allowing the

motor to reach full speed.

5. Repeat step 4. until you hear the lines hitting against the

cutter. (Do not repeat this procedure more than 6 times)

6. If problems are experienced with the automatic line

feed refer to Fault Finding Chart.

line cutter

To manually feed the nylon line (N)

1. If required line can be fed out manually.

2. To operate, press and release manual line feed but-

ton, whilst gently pulling on one of the lines until the

line reaches the line cutter.

3. When the required amount of line is fed out, gently

pull on the second line (there is no need to press the

manual line feed button again).

4. If the line extends past the line cutter, too much line

has been fed out.

5. If too much line is fed out, remove the spool cap and

click spool anti-clockwise until the line is at the desired

length.

Manual line feed

manual line

feed button

Cutting Head

To remove spool cap

1. Press and hold in the two cap release latches. (P).

2. Pull

cap away from the spoolholder. (P).

When r

efitting the spool cap

1. Keep all areas of the cap and spoolholder clean.

Failure to do so may prevent the cap being securely

located in the spoolholder.

2. Replace the cap, pr

essing firmly DOWN towards

the spoolholder to ensure cap is fully located.

3. Check that the cap is correctly fitted by trying to

remove it without depressing the two latches.

o replace nylon line.

For your convenience it is recommended you buy spool

and line complete. Nylon line only is also available. Both

are available from Husqvarna Outdoor Products stockists.

o fit spool and line complete:

1. Remove the cap.

2. Remove old spool.

3. Place spool into spoolholder.

4. Release one line from cleat (R1).

5. Secure line into slot (Q1).

6. Repeat for second line.

• Ensure spool is fully located by gently rotating it during

fitment, whilst keeping the spoolholder steady.

7. Refit the cap.

o fit nylon line only:

• Remember! Your Flymo Trimmer is designed to use

only nylon line with a maximum diameter of

1.5mm. Use only genuine Flymo nylon line.

1. IMPORTANT - Always wind the line onto the

upper section of the spool first.

Take approximately 5 metres of line. Insert 15mm of

line into one of the holes in the upper section of the

spool (R) and wind line in the direction of the arrows

on the top of the spool. Leave approximately 100mm

of line unwound and place into cleat as illustrated in

figure R1. Repeat on lower section of spool.

2. Care should be taken to ensure that the line is neatly

coiled on the spool. Failure to do so will impair the

efficiency of the automatic line feed.

3. Then fit spool as described in ‘To fit spool and line

complete’, section above.

Cap

Cap release

latch

Spool

Spoolholder

Slot

Cleat

Maintenance

• WARNING

Disconnect from the mains electricity supply,

before attempting any maintenance or adjust-

ment. Cutting head continues to rotate after the

trimmer has been switched off. Keep fingers and

hands clear of the line cutter on leading edge of

guard.

Caring for your Contour Power Plus

After you have finished using your Flymo Contour Power

Plus follow the procedure below:

AVOID ACCIDENTAL STARTING. REMOVE PLUG

FROM MAINS AND KEEP FEET AWAY FROM THE

SWITCH LEVER WHEN: CLEANING AROUND THE

INSIDE OF THE SAFETY GUARD, REMOVING OR

REFITTING SPOOL CAP, MANUALLY FEEDING OR

REPLACING NYLON LINE.

1. Disconnect from the mains electricity supply.

2. Never clean your trimmer with water, cleaning fluids,

or solvents, just remove debris with a suitable tool, a

soft brush or dry cloth.

3. Using a soft brush, clean around the inside of the

safety guard, the cutting head (Fig S) and the motor

housing air vents. (Fig T)

4. Remove the wheel by pressing one of the buttons.

Clean the wheel and groove on trimmer head with a

soft brush (V & W).

5. Attach wheel as described in Wheel Assembly.

6. Inspect the trimmer carefully, especially the parts of

the cutting head.

7. If your trimmer is damaged in any way contact your

local approved service centre.

• Never use a damaged trimmer.

8. Store in a cool, dry place and out of reach of chil-

dren.

Cable Storage

1. Your mains cable can be stored on the product as

illustrated in Fig X.

2. Wind cable carefully to avoid kinking.

3. To release the cable press the button and the hook

will drop down (Fig Y).

4. Push cable hook fully back into position.

Flymo Contour PowerPlus Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Flymo Contour PowerPlus

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info