Handleiding Flymo Contour 500 Power Plus (pagina 4 van 9) (Engels)

631003

Verklein

Vergroot

Pagina terug

1/9

Pagina verder

IMPORTANT INFORMATION

Read before use

& retain for future reference

For all customer enquiries or for replacement parts, contact:-

Australia New Zealand

Phone: 1800 802 831 Phone: (09) 920 2410

Email: customer.service@husqvarna.com.au Email: sales@hopnz.co.nz

Carton Contents

IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.

IF ANY PARTS ARE MISSING CONTACT:-

Husqvarna Outdoor Products Customer Service Department direct

Australia New Zealand

Phone : 1800 802 831 Phone : (09) 920 2410

Fax : 1800 802 936 Fax : (09) 920 2429

Safety

General

1. Never allow children or people unfamiliar with these

instructions to use the trimmer. Local regulations

may restrict the age of the operator.

2. Only use the trimmer in the manner and for the func-

tions described in these instructions.

3. Never operate the trimmer when you are tired, ill or

under the influence of alcohol, drugs or medicine.

4. The operator or user is responsible for accidents or

hazards occurring to other people or their property.

Electrical

1. The British Standards Institute recommend the use

of a Residual Current Device (R.C.D.) with a tripping

current of not more than 30mA. Even with a R.C.D.

installed 100% safety cannot be guaranteed and safe

working practice must be followed at all times.

Check your R.C.D . every time you use it.

2. Before use, examine cable for damage. If there are

signs of damage or ageing, it must be replaced by

the manufacturers service agent or a similar quali-

fied person to avoid hazard.

If not used properly this trimmer can be dangerous! This trimmer can cause serious injury to the opera-

tor and others, the warnings and safety instructions must be followed to ensure reasonable safety and

efficiency in using this trimmer. The operator is responsible for following the warning and safety instruc-

tions in this manual and on the trimmer.

Explanation of Symbols on the Contour Power Plus

Warning

Read the user instructions carefully to

make sure you understand all the

controls and what they do.

Keep others, including children, pets and

bystanders outside the 10 metre hazard

zone. Stop the trimmer immediately if you

are approached.

The use of eye protection is recommended

to protect against objects thrown by the cut-

ting line.

To avoid the possibility of electric shock, do

not use in damp or wet conditions.

Switch off! Remove plug from mains before

adjusting, cleaning or if cable is entangled

or damaged.

Warning: The cutting line continues to rotate after the

machine has been switched off.

10m

Switch Handle

Electric Cable with

moulded on plug

Guard

Instruction

Manual

Tube

Steady Handle

Wheel

Trimmer Head

3. Do not use the trimmer if the electric cables are

damaged or worn.

4. Immediately disconnect from the mains electricity sup-

ply if the cable is cut, or the insulation is damaged. Do

not touch the electric cable until the electrical supply

has been disconnected. Do not repair a cut or dam-

aged cable. Replace it with a new one.

5. Your extension cable must be uncoiled, coiled cables

can overheat and reduce the efficiency of your trimmer.

6. Keep the cable clear of the cutting area and obsta-

cles at all times.

7. Do not pull cable around sharp objects.

8. Always switch off at the mains before disconnecting

any plug, cable connector or extension cable.

9. Never pull on the cable to disconnect any of the plugs.

10. Switch off, remove plug from mains and examine

electric supply cable for damage or ageing before

winding cable for storage. Do not repair a damaged

cable, replace it with a new one. Use only Flymo re-

placement cable.

11. Always wind cable carefully, avoiding kinking.

12. Use only on AC mains supply voltage shown on the

product rating label.

13. Flymo trimmers are double insulated to EN60335.

Under no circumstance should an earth be con-

nected to any part of the trimmer.

Preparation

1. While using your product always wear substantial

footwear and long trousers.

2. Before using the machine and after any impact, check

for signs of wear or damage and repair as necessary.

3. Inspect the area to be cut before each use. Remove

all objects such as stones, broken glass, nails, wire,

string etc, which can be thrown or become entan-

gled in the trimmer head.

4 . Check that the cutting head is fitted correctly.

Use

AVOID ACCIDENTAL STARTING. REMOVE PLUG

FROM MAINS AND KEEP FEET AWAY FROM THE

SWITCH LEVER WHEN:- CLEANING AROUND THE

INSIDE OF THE SAFETY GUARD, REMOVING OR

REFITTING SPOOL CAP, MANUALLY FEEDING OR

REPLACING NYLON LINE.

1. Use the trimmer only in daylight or good artificial light.

2. Avoid operating your trimmer in wet grass, where feasible.

3. Take care in wet grass, you may lose your footing.

4. On slopes, be extra careful of your footing and wear

non-slip footwear.

5. Do not walk backwards when trimming, you could

trip. Walk never run.

6. Keep cutting head below waist level.

7. Switch off before pushing the trimmer over surfaces

other than grass.

8. Never operate the trimmer with damaged guards or

without guards in place.

9. Never fit metal cutting elements.

10. Keep hands and feet away from the cutting means at

all times and especially when switching on the motor.

11. Never pick up or carry a trimmer by the cable.

12. Do not lean over the trimmer guard - objects may be

thrown by the cutting line.

13. Remove the plug from the mains :

- before leaving the trimmer unattended for any period;

- before clearing a blockage;

- before checking, cleaning or working on the appliance;

- if you hit an object. Do not use your trimmer until

you are sure that the entire trimmer is in a safe oper-

ating condition;

- if the trimmer starts to vibrate abnormally. Check

immediately. Excessive vibration can cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure the

trimmer is in safe working condition.

2. Replace worn or damaged parts for safety.

3. Only use the replacement cutting line specified for

this product.

4. Only use replacement parts and accessories recom-

mended by Husqvarna Outdoor Products.

5. To avoid the risk of injury keep fingers and hands clear

of the line cutter on the leading edge of the guard.

6. Inspect and maintain the trimmer regularly. Any re-

pairs must be carried out by an authorised repairer.

Cables

IMPORTANT

Use only 1.00mm

size cable up to 40 metres length

maximum.

Maximum rating:

1.00mm

size cable, 10 amps 250 volts AC.

THE CONTOUR POWER PLUS IS SUPPLIED

WITH AN ELECTRIC MAINS CABLE WIRED DI-

RECTLY INTO THE PRODUCT.

1. Flymo Mains Cables and Extension Cables are

available from your local Approved Service Centre.

2. Do not wire an extension cable directly to your product

yourself. Please contact your local Approved Service

Centre for further information on the connectors and

kits available.

3. Only use extension cables specifically designed for

outdoor use.

CONNECTORS

Flymo connectors are suitable for use with 2 core cable

only. Under no circumstances should these connectors

be used for earthed products.

All Flymo connectors and cables are of splashproof con-

struction. They are not waterproof and must not be left

outside permanently nor should they be submerged or

immersed in water. Do not let cable lay or trail through

pools of water or splashed with water from hose pipes.

MAINS PLUG REPLACEMENT

• If the plug supplied is cut off it should be de-

stroyed. There is an electric shock hazard if a

cut off plug is inserted into a 13 amp socket.

1. No earth required. Flymo products are double in-

sulated to EN60335 and under no circumstances

should an earth be connected to any part of the

product.

2. Ensure the mains voltage suits your product.

3. IMPORTANT!

The wires in the mains lead are coloured in accordance

with the following code:

BLUE - NEUTRAL

BROWN - LIVE

The wire which is coloured BLUE must be connected to

the Terminal which is marked with the letter ʻNʼ or

coloured BLACK. The wire which is coloured BROWN

must be connected to the Terminal which is marked with

the letter ʻLʼ or coloured RED.

4. It is important that the outer sheath is clamped cor-

rectly into the 3-pin plug.

5. If in doubt consult your local Service Repairer or

qualified electrician before the machine is used.

Assembly of Switch Handle to Tube (A1)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the switch handle.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Assembly of Trimmer Head to Tube (A2)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the trimmer head.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Safety Guard Assembly (B1) & (B2)

1. Locate the safety guard over the cutting head. En-

sure the nylon line is fed through the hole in the

safety guard as illustrated in fig B1.

2. Push into location and turn safety guard in the direc-

tion illustrated in Fig B2, until a click is heard and the

safety guard is securely locked in position.

• ENSURE THE SAFETY GUARD IS SECURELY IN

PLACE BY ATTEMPTING TO TWIST GUARD.

Wheel Assembly (C1) & (C2)

1. Fix the 2 halves of the wheel together as illustrated in

fig C1.

2. Attach the wheel to the trimmer making sure that it is

located into the groove on the trimmer head (C2).

3. Clip the wheel together on the other side, making

sure it is secure.

4. The wheel should turn freely.

Steady Handle Assembly (D)

1. Depress the two buttons on the sides of the switch handle.

2. Locate the steady handle over the buttons and re-

lease the buttons.

3. Adjust the steady handle to the most comfortable op-

erating position by depressing the buttons and mov-

ing the handle.

Height Adjustment (E)

1. Turn height adjuster (E1) in the direction indicated to

un-lock (E2).

2. Adjust the length of the tube to the most comfortable

operating position.

3. Turn height adjuster in the opposite direction to lock

(E3).

• ENSURE THAT THE TUBE IS FULLY SECURED.

Cable Restraint (F1) & (F2)

1. Form loop in mains cable and push the loop through

the slot as illustrated in picture (F1).

2. To secure, position loop over the hook and pull the cable

back through the slot as illustrated in picture (F2).

Assembly Instructions

C1 C2

Double Auto Feed System

How the automatic line feed works (G)

1. When initially switching on the trimmer, a small length

of line is fed out.

2. A ʻclatteringʼ noise will be heard when the two nylon

lines hit the line cutter. DO NOT BE ALARMED this

is quite normal. After approximately 5 seconds the

line will be cut to the correct length and the noise will

reduce as the motor reaches full speed.

• Make sure the motor is up to full speed before

trimming or edging.

3. If the noise of the nylon line being cut cannot be

heard, more line will need to be fed out.

4. To feed more line, it is first necessary to to allow the

motor to stop completely, then re-start, allowing the

motor to reach full speed.

5. Repeat step 4. until you hear the lines hitting against the

cutter. (Do not repeat this procedure more than 6 times)

6. If problems are experienced with the automatic line

feed refer to Fault Finding Chart.

line cutter

F1 F2

• WARNING

• The use of eye protection is recommended.

Do not lean over the trimmer whilst trimming or

edging, objects may be thrown by the cutting line.

Do not allow cutting head to rest on the ground.

Do not overload your trimmer.

Overloading can be avoided by making sure the

motor speed does not drop unduly.

DISCONNECT FROM THE MAINS ELECTRICITY

SUPPLY BEFORE ATTEMPTING ANY MAINTE-

NANCE OR ADJUSTMENT.

• BEFORE USE

Make sure that both lines are fed out.

• Make sure motor is up to full speed before trim-

ming or edging.

How to trim

1. Hold as illustrated in Fig H.

2. To start, squeeze the switch lever.

3. Cut with nylon line at an angle using the tip. See

Fig J.

4. Swing trimmer in and out of the cutting area tak-

ing small cuts (K)

5. Line is fed out automatically every time the trimmer

head stops rotating and returns to operating speed.

• Extra line can be fed out manually as described in

Manual line feed

6. To stop your trimmer release the switch lever.

How to edge

1. To convert to edging mode, press button (L1) and

twist head (L2). An audible "click" will confirm that the

head is locked.

2. Hold as illustrated in Fig H.

3. To start, squeeze the switch lever.

4. Rest edger on wheel for extra stability and line up the

edge of the lawn with the two indicators on the guard

(M1). Edge in direction indicated in Fig M.

5. To stop your trimmer release the switch lever.

6. To return to trimming mode, press button and twist

head back the opposite way. An audible "click" will

confirm that the head is locked.

How to trim and edge

To manually feed the nylon line (N)

1. If required line can be fed out manually.

2. To operate, press and release manual line feed but-

ton, whilst gently pulling on one of the lines until the

line reaches the line cutter.

3. When the required amount of line is fed out, gently

pull on the second line (there is no need to press the

manual line feed button again).

4. If the line extends past the line cutter, too much line

has been fed out.

5. If too much line is fed out, remove the spool cap and

click spool anti-clockwise until the line is at the desired

length.

Manual line feed

manual line

feed button

Cutting Head

To remove spool cap

1. Press and hold in the two cap release latches. (P).

2. Pull cap away from the spoolholder. (P).

When refitting the spool cap

1. Keep all areas of the cap and spoolholder clean.

Failure to do so may prevent the cap being securely

located in the spoolholder.

2. Replace the cap, pressing firmly DOWN towards

the spoolholder to ensure cap is fully located.

3. Check that the cap is correctly fitted by trying to re-

move it without depressing the two latches.

To replace nylon line.

For your convenience it is recommended you buy spool

and line complete. Nylon line only is also available. Both

are available from Husqvarna Outdoor Products stockists.

To fit spool and line complete:

1. Remove the cap.

2. Remove old spool.

3. Place spool into spoolholder.

4. Release one line from cleat (R1).

5. Secure line into slot (Q1).

6. Repeat for second line.

• Ensure spool is fully located by gently rotating it during

fitment, whilst keeping the spoolholder steady.

7. Refit the cap.

To fit nylon line only:

• Remember! Your Flymo Trimmer is designed to use

only nylon line with a maximum diameter of 1.5mm.

Use only genuine Flymo nylon line.

1. IMPORTANT - Always wind the line onto the upper

section of the spool first.

Take approximately 5 metres of line. Insert 15mm of

line into one of the holes in the upper section of the

spool (R) and wind line in the direction of the arrows

on the top of the spool. Leave approximately 100mm

of line unwound and place into cleat as illustrated in

figure R1. Repeat on lower section of spool.

2. Care should be taken to ensure that the line is neatly

coiled on the spool. Failure to do so will impair the ef-

ficiency of the automatic line feed.

3. Then fit spool as described in ‘To fit spool and line

complete’, section above.

Cap

Cap release

latch

Spool

Spoolholder

Slot

Cleat

Maintenance

• WARNING

Disconnect from the mains electricity supply, be-

fore attempting any maintenance or adjustment.

Cutting head continues to rotate after the trimmer

has been switched off. Keep fingers and hands

clear of the line cutter on leading edge of guard.

Caring for your Contour Power Plus

After you have finished using your Flymo Contour Power

Plus follow the procedure below:

AVOID ACCIDENTAL STARTING. REMOVE PLUG

FROM MAINS AND KEEP FEET AWAY FROM THE

SWITCH LEVER WHEN: CLEANING AROUND THE IN-

SIDE OF THE SAFETY GUARD, REMOVING OR RE-

FITTING SPOOL CAP, MANUALLY FEEDING OR

REPLACING NYLON LINE.

1. Disconnect from the mains electricity supply.

2. Never clean your trimmer with water, cleaning fluids,

or solvents, just remove debris with a suitable tool, a

soft brush or dry cloth.

3. Using a soft brush, clean around the inside of the

safety guard, the cutting head (Fig S) and the motor

housing air vents. (Fig T)

4. Remove the wheel by pressing one of the buttons.

Clean the wheel and groove on trimmer head with a

soft brush (V & W).

5. Attach wheel as described in Wheel Assembly.

6. Inspect the trimmer carefully, especially the parts of

the cutting head.

7. If your trimmer is damaged in any way contact your

local approved service centre.

• Never use a damaged trimmer.

8. Store in a cool, dry place and out of reach of children.

Cable Storage

1. Your mains cable can be stored on the product as il-

lustrated in Fig X.

2. Wind cable carefully to avoid kinking.

3. To release the cable press the button and the hook

will drop down (Fig Y).

4. Push cable hook fully back into position.

Fault Finding Chart

WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.

FAULT CHECK ACTION

Is the automatic line feed work-

ing?

Manually feed out line.

SEE “MANUAL LINE FEED”

Is the line fed out and visible?

Has line been removed from

cleat?

Remove cap and spool, free line

and re-fit spool and cap. SEE

“CUTTING HEAD”

The line may be jammed on the

spool. Rewind line to remove

crossed loops. Check that line is in

correct section of spool.

Is the manual line feed working?

Has too much line been fed out?

SEE “MANUAL LINE FEED”

Contact your local approved

Service Centre or Husqvarna

Outdoor Products Customer

Service.

Is the line cutter missing from the

safety guard?

Contact Husqvarna Outdoor Products Customer Service

Australia

New Zealand

Phone: 1800 802 831 Phone: (09) 920 2410

Yes

LINE NOT FEEDING

LINE TOO SHORT

TRIMMER VIBRATES

CONTINUOUS CLATTER-

ING NOISE

LINE SNAPS CONTINU-

OUSLY

IF NONE OF THE ABOVE

OR IF FAULT PERSISTS

Has the motor reached full

speed before use?

Allow the motor to reach full speed

before use.

Are you using the trimmer cor-

rectly?

Only use tip of nylon line to trim.

SEE “How to trim and edge”

Is the line jamming on the spool?

Yes

Rewind the line on the spool, if

symptoms still persist, change

spool and line.

Clean wheel and groove on trimmer head. SEE “MAINTENANCE”

WHEEL STOPS TURNING

If any part is found to be defective due to faulty manufacture

within the guarantee period, Husqvarna Outdoor Products,

through its Authorised Service Repairers will effect the repair or

replacement to the customer free of charge providing:

(a) The fault is reported directly to the Authorised Repairer.

(b) Proof of purchase is provided.

ment by the user.

(d) The failure has not occurred through fair wear and tear.

(e) The machine has not been serviced or repaired, taken apart

or tampered with by any person not authorised by Husqvarna

Outdoor Products.

(f) The machine has not been used for hire.

(g) The machine is owned by the original purchaser.

(h) The machine has not been used commercially.

* This guarantee is additional to, and in no way diminishes the

customers statutory rights.

Failures due to the following are not covered, therefore it is impor-

tant that you read the instructions contained in this Operator's Man-

ual and understand how to operate and maintain your machine:

Failures not covered by guarantee

* Replacing Nylon Line.

* Failures as a result of not reporting an initial fault.

* Failures as a result of sudden impact.

* Failures as a result of not using the product in accordance

with the instructions and recommendations contained in this

Operator's Manual.

* Machines used for hire are not covered by this guarantee.

* The following items listed are considered as wearing parts

and their life is dependent on regular maintenance and are,

therefore not normally subject to a valid warranty claim: Nylon

Line, Spool and Line, Electric Mains Cable

* Caution!

Husqvarna Outdoor Products does not accept liability under

the warranty for defects caused in whole or part, directly or

indirectly by the fitting of replacement parts or additional parts

that are not either manufactured or approved by Husqvarna

Outdoor Products, or by the machine having been modified in

any way.

Guarantee & Guarantee Policy

• Awareness of the environment must be considered

when disposing of ʻend-of-lifeʼ product.

• If necessary, contact your local authority for disposal

information.

The symbol on the product or on its packaging indi-

cates that this product may not be treated as household

waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and elec-

tronic equipment.

By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the

environment and human health, which could otherwise

be caused by inappropriate waste handling of this prod-

uct.

For more detailed information about recycling of this

product, please contact your local council office, your

household waste disposal service or the shop where

you purchased the product.

Environmental Information

1150916-28

Husqvarna Outdoor Products Pty Ltd

Locked bag 18, Gosford

NSW 2250

Australia

Tel: 02 4372 1500

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.

Newton Aycliffe, 15/08/2007

M. Bowden,

Research & Development Director

EC Declaration of Conformity

I, the undersigned M. Bowden of Husqvarna

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5

6UP. Certify that the product:-

Category........ Electric Lawn Trimmer

Make.............. Husqvarna Outdoor

Products

Conforms to the specifications of Directive

2000/14/EC

I, the undersigned M. Bowden of Husqvarna

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5 6UP

Certify the maximum weighted sound pres-

sure level recorded on a sample of the

above product at the operator position under

free field conditions was: -

I, the undersigned M. Bowden of Husqvarna

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5

6UP

Certify the maximum weighted root

mean square value recorded on a sample of

the above product at the operators hand po-

sition was: -

Type of Cutting Device.............. Cutting Line

Identification of Series............... See Product Rating Label

Conformity Assessment Procedure....ANNEX VI

Notified Body.........................Intertek, Cleeve Road, Leatherhead,

Surrey. KT22 7SB England

Other Directives:-.......................98/37/EC, 89/336/EEC,

73/23/EEC

& applicable standards:- EN786, EN60335-1, EN60335-2-91,

EN61000-3-2, EN61000-3-3, EN55014-1, EN50366

Type........................................................ EIT250 EIT300

Width of Cut............................................ 25 cm 30 cm

Speed of Rotation of Cutting Device....... 10500 RPM 10300 RPM

Guaranteed sound power level............... 96 dB (A) 96 dB(A)

Measured Sound Power Level................ 91 dB (A) 95 dB (A)

Level........................................................79 dB (A) 81.8 dB (A)

Value....................................................... 2.91 m/s

1.37 m/s

Weight..................................................... 3.26 kg 3.45 kg

Husqvarna Outdoor Products

PO Box 76-437, Manukau City

Auckland

New Zealand

Tel: 9 920 2410

Flymo Contour 500 Power Plus Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Flymo Contour 500 Power Plus

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info