763940
63
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
Operating the Meter Using the Computer Interface
Introduction 4
4-3
Introduction
This chapter describes how to set up, configure and operate the Meter via the RS-232
computer interface on the Meter’s rear panel. The Meter can be operated from a host (a
terminal, controller, PC, or computer) by sending commands to the Meter through its
computer interface.
An annotated sample program illustrating the use of the RS-232 computer interface is
provided at the end of this chapter. Refer to Chapter 3 for complete descriptions of all
Meter functions and features.
This chapter assumes that you are familiar with the basics of data communication and
RS-232 interface.
Local and Remote Operations
When the Meter is operated from a host, it is said to be operated remotely. When the
Meter is operated from its front panel, it is said to be operated locally.
Most operations that can be performed locally can also be performed remotely using the
computer interface. Some operations, like setting communications parameters for the RS-
232 interface operations, can only be performed from the front panel.
Computer Interfaces
The Meter comes equipped with an RS-232 (serial) interface. Using the interface turns
the Meter into a fully programmable instrument that can be integrated into an automated
instrumentation system.
Preparing the Meter for Operations via the RS-232 Interface
The RS-232 interface allows ASCII asynchronous serial communication between the
Meter and a host, serial printer or terminal.
Setting Communication Parameters (RS-232)
Table 4-1 provides the RS-232 communication parameters factory settings. Setting RS-
232 communication parameters is only performed through the front panel.
In order for the Meter and host to communicate via the RS-232 interface, the
communication parameters of the Meter must match those of the host. If the
communications parameters of the host and Meter do not match, set the appropriate baud
rate and parity parameters as follows:
1. Press P to turn the Meter on.
2. Press Q then K. The baud rate currently selected is shown in the primary
display and baud is shown in the secondary display.
3. Press U or V to scroll to the desired baud, and then press R to set the
RS-232 baud rate.
4. Press U or V to scroll to the desired data bit (7 or 8) selection, then press
R to set parity. Echo appears on the secondary display, and 0n or 0FF appears
on the primary display.
5. To select an Echo mode, press U or V to select On or OFF, and then press
R to set the selected Echo state. When Echo is on, each command sent to the
Meter over the RS-232 interface is echoed to the host's display screen. When
Echo is off, commands are not echoed.
63

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 8808A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 8808A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Fluke 8808A

Fluke 8808A Gebruiksaanwijzing - Deutsch - 102 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info