763940
56
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
8808A
Users Manual
3-22
Table 3-6. Second Level Operations (cont.)
Buttons Description
Q and V[1] In COMP mode, stores value on primary display as LO compare point (see
the “Using the Compare Function” section later in this manual)
Q and U[1] In COMP mode, stores value on primary display as HI compare point (see
“Using the Compare Function”)
[1] Hold both buttons for 2 seconds.
Compare Function (COMP)
The Meter has a compare function (COMP) that provides an easy way to determine if a
reading falls within a designated range of values. The compare function can be used with
any function modifier.
Setting the Compare Range
Before selecting the compare function, you need to set the tolerance range against which
the reading that will be compared. This can be done in any of the following three ways:
Press C to enter the compare function mode. The reading displayed when you
enter the mode can be set to the high or low threshold. To set the reading as the
high limit, press and hold Sand U for 2 seconds. To set the reading as the
low limit, press and hold Sand V for 2 seconds. The Meter beeps to
indicate the limit has been set. If the display is blank or shows 0L (overload), the
limit could not be set and the high and low limits remain as previously set.
Use the number editor as described in the “Using the Number Editor” section
later in the chapter. (Before entering the number editor, be sure you are in the
appropriate range.) The decimal point and input range are fixed according to the
range in the editor.
Use the computer interface commands COMPHI and COMPLO to set the high and
low compare points remotely. See the “Compare Commands and Queries”
section in Chapter 4.
Using the Compare Function
To select the compare function, press C. When the compare function is first selected,
the Touch Hold function is also activated and H is displayed. To turn off Touch
Hold, press and hold I for 2 seconds. The secondary display will then update with
each new reading.
When a stable value is detected, the Meter beeps if hold is on and the reading is shown in
the primary display. If the value is within the range you set, PASS is shown in the
secondary display. If the value is not within the set range, HI or L0 is shown as applicable
in the secondary display.
List and Number Editors
The Meter has a list editor and number editor. The list editor allows you to scroll through
and select from a list of options. The number editor allows you to enter or edit a numeric
value.
Editing is performed in the primary display. Normal operation of the Meter is interrupted
when either editor is invoked. If a computer interface command is received by the Meter
during editing, the edit is aborted and the Meter returns to normal operation. The item
being edited is not changed.
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 8808A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 8808A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Fluke 8808A

Fluke 8808A Gebruiksaanwijzing - Deutsch - 102 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info