775826
70
Verklein
Vergroot
Pagina terug
1/98
Pagina verder
190 Series III
Users Manual
64
Current Unbalance
Current Unbalance checks for the difference between current levels of the phases for 3-phase
systems. To calculate the unbalance value:
% unbalance = (maximum deviation from average / average of three phases) x 100 %
Tips:
Current unbalance should be <6 % and depends on load current and circuit capacity.
Excessive current unbalance can point to or cause drive rectifier problems that result in the
motor overheating. Current unbalance can be caused by voltage unbalance. For example,
1 % of voltage unbalance can result in 3 % to 4 % of current unbalance.
2 changes the readings that are displayed in the top of the screen to the peak-peak
values of each phase as well as the highest Crest Factor (ratio between peak and rms value)
of one of the phases.
Harmonics
Harmonics are periodic distortions of the voltage and current sine wave. Harmonics occur when
multiples of the fundamental waveform are superimposed over the fundamental. You can
consider the signal as a combination of various sine waves with different frequencies. The
contribution of each of these components to the full signal is shown as a bar. For example, a 5th
harmonic is 300 Hz (5 x 60) for 60 Hz systems or 250 Hz (5 x 50) for 50 Hz systems. The effect of
these harmonics is distortion of the voltage or current. The sum of all distortions from the 2nd
harmonic to the 50th harmonic divided by the fundamental component is expressed as the Total
Harmonic Distortion (THD).
The readings in the top of the screen show the ac rms value of the signal, the fundamental (H1)
value, the frequency of the fundamental and the THD value.
To view the reading for the harmonic component:
1. Select 4 Harmonics.
2. Push 2 Input to select the channel for the harmonics display.
For Voltage and Current measurements, select A for the Voltage harmonics on Channel A
and select B for the Current harmonics on Channel B.
For Unbalance measurements, select A, B, or C to show the voltage or current harmonics for
the selected channel.
3. Push h to vertically zoom in on the harmonics display.
4. Push 3 Scale Options to change the vertical scale.
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 190-102-III bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 190-102-III in de taal/talen: Engels als bijlage per email.

De handleiding is 9.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info