Instruction manual
WIRELESS INTERCONNECT
Model:
IMPORTANT INFORMATION
Correct usage will ensure you have valuable extra
time to escape. Every correctly installed smoke detec-
tor will increase your potential escape time.
•
measure.
•
possible in the middle of the ceiling.
WARNING: Read carefully chapter "Never fit a
smoke detector"
•
children.
•
period of absence. When the alarm does not sound,
have your smoke alarm inspected by the service
point or when the smoke alarm is more than 10
years old discard the alarm.
CAUTION: Never test with fire!
•
the soft brush from a vacuum cleaner. In addition
the smoke alarm can also be cleaned using a moist
cloth.
•
seconds, this means that the battery is nearly flat
and that you should replace the smoke detector.
•
•
and silence button.
•
tor less sensitive for 10 ± 2 minutes by
pressing the test button shortly. The detector will
nonetheless sound the alarm if the quantity of
smoke is too significant.
•
using the ASD-RRC. This is the optionally available
wireless remote control.
IMPORTANT INFORMATION IN
ALARM IN THE
• Plan TWO escape routes and practice these with all
members of the family.
•
case of a fire.
In the event of a fire:
•
agreed location.
•
•
door. In case of a warm door, choose a different
escape route.
•
crawl out of the building keeping as close to the
floor as possible.
•
bly moist), or else hold your breath as much as you
can. The majority of deaths and injuries are caused
by smoke inhalation rather than fire itself.
•
• NEVER go back into a burning building.
•
fire department.
SPECIFICA
RF frequency: 868.100 (<1% duty cycle)
RF Codes: 65535
RF Power: +14 dBm max
5)UDQJH PPLQRSHQ¿HOG
Battery life: 10 years under normal
conditions
Battery type: Sealed, Lithium,
&RQVXPSWLRQ ȺVWDQGE\
P$LQDODUP
Operating temperature:
2SHUDWLQJKXPLGLW\ 5+DW&
Alarm sound level: >85dB op 3 meter
Hush time: 10 ± 2min.
&HUWL¿FDWLRQV
POSITIONING THE SMOKE
RECOMMENDED LOCA
Optimal protection:
In all occupied areas such as bedrooms, living room,
study and the escape route as hallway
and attic.
Maximum protection:
- Smoke detector in all rooms (with the exception
of bathrooms, kitchen, garages, etc.)
- Heat detectors can be installed in bathrooms,
kitchens, airing cupboards, utility rooms, etc.
ZLWKLQPHWUHVRIDSRWHQWLDOVRXUFHRI¿UH
•
in the middle of the ceiling, at least 50 cm from the
wall.
•
WRURQWKHVORSLQJZDOODWOHDVWFP
(measured vertically) from the ridge of the roof.
•
testing and cleaning.
Never fit a smoke alarm:
•
etc. Places where a smoke detector may go off
needlessly due to condensation, normal smoke or
gases. A smoke detector should be fitted at least 5
metres from such sources of smoke.
IDOOEHORZ
place, etc.
•
doors, sockets, lights, fittings, windows, wall
ventilators, etc. which could mean that smoke does
not reach the smoke detector. Minimum 50cm
away.
•
rest of the room. Differences in temperature can
prevent smoke from reaching the detector.
•
•
it hard to reach the detector to test or clean it.
•
will prevent smoke from reaching the smoke cham-
ber and in time will lead to a false alarm.
•
dimmer switches can trigger a fault in the detector
•
impulses can adversely affect the functioning of the
detector
•
sects are found. Small insects in the unit’s detection
chamber can disrupt the functioning of the detector
The labels on the rear side of the detector contain
important information.
HOW TO U
Wireless interconnecting the smoke alarms:
The
alarm can be the sender or the receiver
T
code must be generated in one of them and set to
the others
apartment or property should be set to the same RF
Code.
It is not recommended to interconnect more than 24
smoke alarms.
Generating the unique RF Code:
• Remove all smoke alarms from bases.
• Press and hold the test button for about 4 sec. on
one of them (randomly chosen) and release the
button when the red LED will lit. This smoke alarm
(Master) has chosen one of the 65.535 possible RF
codes. The red LED on the Master will be lit until
the interconnect procedure is over
• In order to set the generated code to the other
smoke alarms(Slaves) push the T
each of them. The successful setting of the code to
the Slave will be accompanied with blinking of the
red LED. Y
smoke alarms, after two minutes the red LED will
extinguish indicating that the interconnect proce-
dure has ended.
• T
press the test button on the Master or fasten the
Master on to the base. The red LED will extinguish
indicating that the interconnect procedure has
ended.
How to disconnect a smoke alarm:
If you need to disconnect one smoke alarm carry out
Generating the unique RF Code procedure.
How to add a smoke alarm:
TGe-
nerating the unique RF Code procedure on all the
smoke alarms you want to interconnect.
T
tion:
Install all interconnected smoke alarms to bases.
Press and hold on the T
(T
interlinked smoke alarms will go to the Remote
mode. Upon releasing the T
alarms will stay in the Remote
The installation:
1.
described in: Positioning the smoke detector.
2.
the base plate anticlockwise (to the left).
3. Mark the mounting holes in the base plate and
drill the holes (use a 6 mm drill). If you do not
use the dowels, then use a 3 mm drill. Screw the
base plate securely onto the ceiling. Make sure
that the base plate is tight
against the ceiling so that
no air circulation above the
smoke alarm is possible,
which could impede smoke
detection.
If the opening is too large,
this must be remedied by
the use of a filler.
If you use the double sided
tape, make sure the base
and the surface you want
to install the smoke alarm
is grease free.
base and then the base to the ceiling.
4.
until the smoke detector clicks into the base. Turn
the smoke detector clockwise to secure the smoke
detector and activate it. A melody will sound to
confirm the activation.
5. T
procedure as described in chapter: "T
the smoke alarms and the interconnection"
AThe smoke alarm should be covered
or temporarily removed during renovation work or
structural alterations. Once the day’s work is com-
plete, clean the smoke detector with the soft brush
from a vacuum cleaner and then activate it again.
Always test it by pressing the test button once it has
been reinstalled.
W covering the smoke alarm causes loses
its functionality
W Do not paint the smoke alarm.
QHYHUWHVWWKHVPRNHDODUPZLWK¿UHRUVLJDUHWWHV
CAUSES OF FALSE ALARM
The smoke detector can be activated by steam, con-
densation, dust, smoke and small insects. These are
to be prevented as much as possible. See chapter
"Never fit a smoke alarm" . If a smoke alarm fre-
quently gives a false alarm, it might be necessary to
install the detector in another location.
Additional information can be found on our website
ZZZ-
tioning correctly
)LWR3URGXFWV%9ZZZ
MAINTENANCE
•
Test your smoke alarm regularly, once a month and
always after a period of absence. See "
T
smoke alarms and the interconnection"
•
the soft brush from a vacuum cleaner
the smoke alarm can also be cleaned using a moist
cloth.
•
ÀXLGV
LIMITATIONS OF SMOKE
In countries where they are commonly in use, smoke
detectors have contributed to reducing deaths and
injuries. Independent bodies have established that
they were insufficient in around 35% of fires, namely
in the following situations:
•
working. For that reason, you should test the unit
regularly.
•
the event of a fire, meaning the unit cannot be set
off. Examples include a fire on another floor where
there is no smoke detector, a fire behind closed
doors, a fire in a chimney or smoke being blown
away from the detector. For that reason, smoke
detectors are recommended in all rooms, or at any
rate on every floor.
•
woken by the alarm if that person had consumed
excess alcohol and/or drugs.
•
smoking in bed, if there is no smoke detector in the
bedroom. In the case of escaping from gas or
violent explosions, improperly storing explosive pro-
ducts and flammable liquids (petrol, paint, methyla-
ted spirit, etc.), electrical faults, acids, children
playing with matches (fire).
•
PRODUCT WARRANTY
If used and maintained properly, the manufacturer
guarantees this product against material and/or
manufacturing defects for a period of 5 years from the
original date of purchase. This guarantee only applies
if the smoke detector is activated within 14 months
after the production date. Exceptions include damage
arising from accidents or misuse. If the product
becomes defective within the stated period, then it will
be repaired or replaced free of charge. Please do not
open the smoke alarm or attempt to repair the
product yourself or tinker with it, which will invalidate
the warranty.
WARNING:Unscrewing the smoke alarm invalidates
the warranty.
DO
The DoP can be downloaded on our website www.
fito.eu
INSTRUCTIONS FOR REMOVAL
Do not dispose of your old detector in
the bin, but rather hand it in to a local col-
lection point for small, domestic waste.
EUROPEAN SUPPLIER:
Fito Products BV
De Langkamp 12a
06
WIJK BIJ DUURSTEDE
Nederland
info@fito.nl - www.fito.eu
Base
Mounting holes:
SAFETY ISSUES:
•
Do not paint to the smoke alarm and do not cover it.
• Never install smoke detectors in rooms with a high humidity, such
as bathrooms, showers, kitchens and saunas.
• Test your smoke alarm regularly, once a month and always after
a period of absence. Test by pressing the test button for at least 2
seconds, a loud alarm will follow. Keep a distance of at least 50 cm.
between the alarm and your ears.
• Never open the smoke alarm, this will invalidate the warranty.
• Do not test with smoke directly after instalation, wait at least 1 hour.
figure 4
red LED
Test/hush
button
kitchen
living room
bathroom
bedroom
hallway
figure 1
bedroom
bedroom
bedroom
bedroom bedroomhallway
kitchen hallway living room
Basement
figure 2
RETAIN THESE INSTRUCTIONS FOR FUTURE USE!
These instructions contain important information for correct instal-
lation and use of your smoke detector. Please read this informa-
tion carefully and retain these instructions for future
reference.
Sound signal: Red LED: Function:
No signal Flashes every
320 sec.
Standby mode
Periodical automatic self-diagnostics
Long pulsating sound Flashes every
0.5 sec. Alarm status
Long lingering sound Non 1 of the interconnected smoke alarms are in alarm
1 short signal every 40 sec. Non Low battery signal. The smoke alarm needs to be
replaced.
2 short signals every 4 hour Non Low battery signal in one of the interconnected smoke
alarms. This smoke alarm needs to be replaced.
3 short signals every 40 sec. Non Fault/ smoke chamber contamination
No signal Flashes every
0.5 sec.
The smoke chamber has been abruptly contaminated
and needs to be cleaned.
No signal Flashes every
10 sec. HUSH mode (Alarm muting, sensitivity reduction)
Long pulsating sound while
pressing the test button.
Flashes every
0.5 sec.
T
interconnected and installed to the base smoke alarms
will go to Remote
3 short signals while pressing
the test button.
Flashes every
3 sec.
De smoke alarm does not operate correctly and needs
to be replaced.
• When the
sound that belongs to the detected problem.
• The remaining connected
base), up to 4 hours after removal of the
FUNCTION AND MEANING OF LIGHT
versie 1 2021-6
1
EN14604:2005/AC 2008
Essential characteristics: Pe
Nominal activation conditions/sensitivity
WLPHDQGSHUIRUPDQFHXQGHU¿UHFRQGLWLRQV
Passed
Fito Products BV
De Langkamp 12a
06:LMNELM'XXUVWHGH
The Netherlands
17
Operational reliability: Passed
T Passed
Durability of operational reliability and response delay
resistance:
Passed
Durability of operational reliability Passed
Optical smoke detector
alerts you in the event
RI¿UHRUVPRNHDQGLV
suitable for residential
buildings.
Durability of operational reliability Passed
Durability of operational reliability Passed
Durability of operational reliability Passed
&KDUDFWHULVWLFVFHUWL¿HGE\$13,
Ceiling mount YES
Battery powered YES
Battery lifetime 10 years YES
Individual Alarm YES
Alarm silence facility YES
Suitable for installation in a
caravan NO
Wireless interconnectable up
to 24 pcs. YES
EN14604:2005/AC 2008
vfdb 14/01
1134-CPR-199
DoP no: 10QR16
RED
17
