795159
13
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
Page 13
Power On/Off
To power the system On/Off, connect the power cable to the DC 12V port on the rear panel. Press the toggle
switch to the on position in the back of the DVR. At startup, the system performs a basic system check
and runs an initial loading sequence. After a few moments, the system loads a live display view.
User Login
Password
ATTENTION: By default, passwords are disabled on the system. You
do not need to enter a password when accessing any system menus.
However, for security purposes, it is highly recommended to enable
passwords on the system using the Password Menu. See “Password”
section for details on setting up passwords. Right click and
select Login. No password is required when no password is
set up. Right click again to show the quick access menu
Quick Access Menu
When using the mouse, use the Quick Access Menu to
access several system options, including the System
Setup Menu. Select one of the following options:
System Setup: Opens the main system menu
View Layout: Provides a choice of viewing channels on the
monitor
• View 1: Allows viewing of 1 channel
• PIP: Allows viewing of 2 channels,
Picture in Picture
• View 4: Allows viewing of 4 channels
• View 8: Allows viewing of channels 1
through 8, with channel 1 in large view mode
• Split 9: Allows viewing of
channels in a 3 x 3 channel grid
• Split 16: Allows viewing of
channels in a 4 x 4 channel grid
Video Adjust: Adjust video image settings by channel
PTZ: Opens the PTZ control menu
Clients: Network user status
Snapshot: Allows you to take a photo of the
channel that the cursor is on, and save to HDD
Photos: Review save Snapshots, and upload to USB drive
Record Setup: Access to recording settings
for each channel, begin manual recording
Playback: Open the Search Menu
and playback recorded video
Clear Alarm: Cancel alarms
Shutdown: Allows a choice of logging out,
powering down or restarting the DVR system
INITIAL SETUP
SYSTEM OPERATION
Main Viewing Screen
User Login Menu
Power Switch
NOTE: Powering down stops the system. The power LED is still on. The only way to fully power down
the system is by turning the power off & on with the power switch on the back of the DVR.
System Start Up
Powering your DVR and Cameras
The power supply included with the DVR is rated for 5 amps. Normally, this is enough to power both the
DVR and supplied cameras. However, using aftermarket cameras or a larger number of cameras may sur-
pass the capability of the power supply, causing the systerm to shut down. Most devices should be marked
with the Amperage rating, but some may be marked by wattage. In this case, Amp usage can be found by
dividing Watts by Volts, or A=W/V. The power supply should be upgraded if it surpasses 80% of its rating
(i.e., 4 amps for a 5 amp power supply), to compensate for momentary spikes in current draw. Note: One Amp equals 1000 milliamps
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw First Alert DVRAD0805 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van First Alert DVRAD0805 in de taal/talen: Engels als bijlage per email.

De handleiding is 4.43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info