456443
9
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
40069 Zola Predosa (BO) - ITALY
info@finicompressors.it
- GB -
2.3 INSTALLATION SITE
Particular care is required in selecting the installation site, as an improper location could
jeopardise the proper operation of the dryer. This unit is not suitable to be used in explosive
atmosphere, where risk of fire could exist, or in presence of gaseous or solid polluting material.
Don’t use water to extinguish fire on the dryer on in the surrounding area.
Minimal installation requirements :
Select a clean room dry, free from dust, and protected from atmospheric disturbances.
The supporting area must be smooth, horizontal and able to hold the weight of the dryer.
Minimum ambient temperature of +1 ºC.
Maximum ambient temperature of +45 ºC.
Allow at list a clearance of 1 m on each side of the dryer for proper ventilation and to facilitate eventual
maintenance operations
.
The dryer doesn't require to be fixed to the supporting surface.
2.4 ASSEMBLING
Operations to be performed by qualified personnel.
Never operate with plants under pressure.
The user is responsible to ensure that the dryer will never be operated with pressure exceeding the
nominal values. Eventual over-pressure could be dangerous both for the operator and the machine.
1
Dryer
2
Cover panel
3
Fixing to compressor
upper screw
4
Compressor
5
Fixing to compressor
lower screw
6
Compression fitting
7
Connection pipe
8
Compression fitting
9
By-pass group
10
Lifting lug
Fig. 1 Fig. 3 Fig. 4
Fig. 2
2
1
6
3
Part. A
5
4
6
7
8
9
3 3
Part. A
10
Assembling sequence :
Replace the screws No.3 of the compressor, with the (M6x45) fixing screws supplied with the dryer, and
thigh them only partially.
Tight in the air outlet of compressor the compression fitting No.6, supplied with the assembling kit.
Remove the cover panel No.2 of the dryer.
Joint the dryer with the compressor, centring the holes of the dryer frame, with the screws No.3 (Fig. 3).
To lift the dryer from the ground, use the four lifting lug No.10 (M6 with long shank) screwed into the four
holes for cover panel fixing.
Slide down the dryer, so the screws No.3 occupy the upper part of the holes (Fig. 4).
Tighten definitively the fixing screws No.3.
Tight the (M8x25) fixing screws, supplied with the assembling kit, in the position No.5 to fix finally the dryer
to the compressor.
Put the connection pipe No.7 from the compression fittings No.6 and No.8 and tighten them.
Connect and properly fasten the condensate drain pipe, in compliance with the instructions given in the
2.7 following chapter.
Slowly pressurize the plant and check for air leakage.
Reassemble the cover panel No.2
.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Finicompressors Artic 134-EVO luchtdroger bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Finicompressors Artic 134-EVO luchtdroger in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info