456445
6
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 17 of 63
3.3 PARAMETERS PROGRAMMING
HOW TO CHANGE THE SET POINT
Press the SET key (the display will show the set point value previously set).
Change the set point value displayed using the UP / DOWN keys (the change must be made within 15
seconds after having pressed the SET key, other ways the controller goes automatically to the normal
operation mode, and the DEW POINT value will be displayed without the possibility to change the SET
POINT).
Confirm the new value by pressing the SET key (this key must be pressed within 10 seconds after the end
of the previous operation, other ways the controller goes automatically to the normal operation mode, and
the DEW POINT value will be displayed without any change to the SET POINT).
The newly entered SET POINT value will blink to confirm that new data have been accepted and stored. 15
seconds later, the controller will return to the normal operation mode.
CONTROL AND CHANGE OF CONFIGURATION PARAMETERS
Hold down the SET key for 10 seconds to access the parameters configuration menu: the display will show
in sequence the set point value, the code of the first E1 modifiable parameter, and its value).
Only if strictly necessary, use the keys UP and/or DOWN to change the value of the displayed parameter.
Press the SET key to store the value of the parameter previously changed, or to browse the parameters
without changing them.
15 seconds after the last performed operation, the controller will go automatically to the normal operation
mode.
NOTE: Changes entered for timing values will be effective only after exiting the programming, while changes to other
variables will be immediately effective.
Please remember that eventual changes to the configuration parameters of the machine could negatively affect its
efficiency. Thus, changes have to be arranged in collaboration with the manufacturer.
3.4 BEFORE START UP
Before to start the machine, make sure that all the operating parameters correspond to the nominal data.
The dryer is supplied already tested and preset for normal operation, and it doesn’t require any calibration.
Nevertheless, during few hours after start up it has to be checked for proper operation.
3.5 START UP
The operations specified below must be performed after the first start up and at each start up after a
prolonged inactive period of time due to maintenance operations, o any other reason.
Make sure that all instructions contained in chapters INSTALLATION SITE and INSTALLATION
have been respected.
Check for proper closure the by-pass system (if present) .
Activate the mains and press the illuminated switch on the control panel of the dryer.
Wait a couple of minutes to let the machine reach the standard operating parameters
Open slowly the air outlet valve and, successively, again slowly, open the air inlet valve.
If present, close the by-pass system.
Check the condensate drain system for proper operation.
Check for proper tightness and stability all the connecting tubing.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Finicompressors Artic 134-12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Finicompressors Artic 134-12 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Finicompressors Artic 134-12

Finicompressors Artic 134-12 Gebruiksaanwijzing - Deutsch - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info