778606
17
Verklein
Vergroot
Pagina terug
1/93
Pagina verder
Close the clamping lever.
7.2 Adjusting the saw blade guidance
To be better able to guide the saw blade, pen
dulum jigsaws have an additional carbide
guide [3-2] immediately above the workpiece.
Tighten the screw [3-3] using the allen
key [1-5] until the jaws are almost touching
the saw blade.
It must be possible to move the saw blade
slightly.
7.3 Inserting the splinterguard
The splinterguard prevents the edges of the
material from splintering during the cut, even
at the end where the saw blade exits the mate
rial.
Switch off the machine and slide the splin
terguard [4-3] onto the guide [4-2] and up
to the saw blade.
Switch on the jigsaw.
With the machine running, push the splin
terguard in on a flat plane until it is flush
with the front edge of the saw table. This
cuts into the splinterguard.
To guarantee reliable operation of the
splinterguard, it must seal tightly on both
sides of the saw blade. A new splinter
guard should therefore be fitted after ev
ery saw blade change to guarantee splint
er-free cuts.
7.4 Inserting the chip guard
The chip guard prevents chips from flying away
and improves the efficiency of the chip extrac
tion system.
Insert the chip guard [2-10] between the
saw table and the clamping lever.
Gently slide the chip guard back until it en
gages.
7.5 Adjusting the saw table
For bevel cuts, the saw table can be swivelled
to either side by up to 45°.
Remove the chip guard and the splinter
guard.
Open the clamping screw [4-1] with the al
len key .
Slide the saw table forwards by approx.
5 mm.
Set the desired inclination using the
scale [5-2].
Tighten the clamping screw [4-1].
To saw close to the edges, the saw table can be
shifted backwards.
Remove the chip guard and the splinter
guard.
Open the clamping screw [4-1] with the al
len key .
Slide the saw table into the rear position so
that the centring mandrel [5-1] slots into
the opening [5-3].
Tighten the clamping screw [4-1].
7.6 Adjusting the pendulum stroke
The pendulum stroke on pendulum jigsaws can
be adjusted to machine different materials with
the correct rate of advance. Select the required
setting using the pendulum stroke switch [1-6]:
Position 0 = pendulum stroke off
Position 3 = maximum pendulum stroke
Recommended pendulum stroke setting
Hardwood, softwood, chipboard, wood
fibreboard 1 - 3
Blockboard, plywood, plastic 1 - 2
Ceramics 0
Aluminium, non-ferrous metals 0 - 2
Steel 0 - 1
7.7 Stroke speed control
The stroke rate can be continuously adjusted
between 1000 and 2900 min-1 using the adjust
ing wheel [1-3; 2-4]. This enables you to opti
mise the cutting speed to suit the respective
material.
Recommended stroke speed (position of the
adjusting wheel)
Hard and soft wood, blockboard, ply
wood, chipboard 6
Fibreboard 4 - 6
Plastic 3 - 6
Ceramic, aluminium, non-ferrous
metals 3 - 5
Steel 2 - 4
7.8 Extraction
WARNING
Health risk due to dust
Always work with an extractor.
Comply with national regulations.
The extraction adapter [2-5] allows jigsaws to
be connected to a dust extractor (hose diameter
27 mm).
English
17
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool Trion PS 300 EQ - 2021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool Trion PS 300 EQ - 2021 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info