778502
28
Verklein
Vergroot
Pagina terug
1/276
Pagina verder
2.2 Safety warnings for bench-mounted
circular saws
1) Guarding related warnings
Keep guards in place. Guards must be in
working order and be properly mounted. A
guard that is loose, damaged, or is not
functioning correctly must be repaired or
replaced.
Always use saw blade guard, riving knife
and anti-kickback device for every
through–cutting operation. For through-
cutting operations where the saw blade
cuts completely through the thickness of
the workpiece, the guard and other safety
devices help reduce the risk of injury.
Immediately reattach the guarding system
after completing an operation (such as
rabbeting, dadoing or resawing cuts)
which requires removal of the guard, riv
ing knife and/or anti-kickback device. The
guard, riving knife, and anti-kickback de
vice help to reduce the risk of injury.
Make sure the saw blade is not contacting
the guard, riving knife or the workpiece
before the switch is turned on. Inadvertent
contact of these items with the saw blade
could cause a hazardous condition.
Adjust the riving knife as described in this
instruction manual. Incorrect spacing, po
sitioning and alignment can make the riving
knife ineffective in reducing the likelihood
of kickback.
For the riving knife and anti-kickback de
vice to work, they must be engaged in the
workpiece. The riving knife and anti-kick
back device are ineffective when cutting
workpieces that are too short to be engag
ed with the riving knife and anti-kickback
device. Under these conditions a kickback
cannot be prevented by the riving knife and
anti-kickback device.
Use the appropriate saw blade for the riv
ing knife. For the riving knife to function
properly, the saw blade diameter must
match the appropriate riving knife and the
body of the saw blade must be thinner than
the thickness of the riving knife and the
cutting width of the saw blade must be wid
er than the thickness of the riving knife.
2) Cutting procedures warnings
DANGER: Never place your fingers
or hands in the vicinity or in line with the
saw blade. A moment of inattention or a
slip could direct your hand towards the saw
blade and result in serious personal injury.
Feed the workpiece into the saw blade or
cutter only against the direction of rota
tion. Feeding the workpiece in the same di
rection that the saw blade is rotating above
the table may result in the workpiece, and
your hand, being pulled into the saw blade.
Never use the mitre gauge to feed the
workpiece when ripping and do not use
the rip fence as a length stop when cross
cutting with the mitre gauge. Guiding the
workpiece with the rip fence and the mitre
gauge at the same time increases the like
lihood of saw blade binding and kickback.
When ripping, always apply the workpiece
feeding force between the fence and the
saw blade. Use a push stick when the dis
tance between the fence and the saw
blade is less than 150 mm, and use a push
block when this distance is less than 50
mm. “Work helping” devices will keep your
hand at a safe distance from the saw blade.
Use only the push stick provided by the
manufacturer or constructed in accord
ance with the instructions. This push stick
provides sufficient distance of the hand
from the saw blade.
Never use a damaged or cut push stick. A
damaged push stick may break causing
your hand to slip into the saw blade.
Do not perform any operation “freehand”.
Always use either the rip fence or the mi
tre gauge to position and guide the work
piece. “Freehand” means using your hands
to support or guide the workpiece, in lieu of
a rip fence or mitre gauge. Freehand saw
ing leads to misalignment, binding and
kickback.
Never reach around or over a rotating saw
blade. Reaching for a workpiece may lead
to accidental contact with the moving saw
blade.
Provide auxiliary workpiece support to the
rear and/or sides of the saw table for long
and/or wide workpieces to keep them lev
el. A long and/or wide workpiece has a ten
dency to pivot on the table’s edge, causing
loss of control, saw blade binding and kick
back.
Feed workpiece at an even pace. Do not
bend or twist the workpiece. If jamming
occurs, turn the tool off immediately, un
English
28
28

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Festool-TKS-80-EBS

Zoeken resetten

  • als ik op de startknop druk gaat de zaag draaien en als ik hem loslaat stop de zaag.
    dan knippert de groene led 3 seconden snel, dan 2 sec rood en groen snel, dan groen 8x en rood 2x en dat blijft zo. ik heb de cartridge vervangen maar de storing blijft. wat kan ik hier aan doen? Gesteld op 22-11-2024 om 14:11

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TKS 80 EBS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TKS 80 EBS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8.85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info