574934
16
Verklein
Vergroot
Pagina terug
1/90
Pagina verder
16
TI 15
GB
Turn the clamping ring as far as the stop to se-
cure the adapter.
Angle attachment DD-AS [7]
Drilling and screwing at right angle to machine
(partly as an accessory).
Eccentric attachment DD-ES [8]
Screwdriving near edges with bits according to ISO
1173 (partly as accessory).
9 Working with the machine
9.1 Operating modes
Depending on the tool holder / adapter selected,
the machine is operated as follows:
9.2 On/Off switch [1-2]
Press = ON, release = OFF
Depending on the pressure applied to the ON/
OFF switch the speed/impact rate can be con-
trolled continuously.
The LED bulb
[1-4]
lights up when the ON/OFF
switch is pressed
[1-2]
.
9.3 Bit depot [1-1]
Magnetic, for storing bits and bit holders.
9.4 Belt clip [1-9]
For short-term fixing of the device to work attire:
can be moved to the right or left or can also be de-
tached from the battery pack.
9.5 Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at:
www.festool.com/Service
Use only original Festool spare parts!
Order No. at:
www.festool.com/Service
Note the following information:
Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
Protect battery packs from moisture, water and
heat.
Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
Screwing with impact
WH-CE CENTROTEC tool chuck (see
Chapter CENTROTEC tool chuck [4])
Screwing and drilling without impact
TI-FX adapter (see Chapter TI-FX adapter
[6])
DD-AS elbow adapter
DD-ES eccentric attachment
DD-DC screwdriver attachment
– BF-TI 13 chuck (see Chapter BF-TI 13
chuck [5])
WARNING
Risk of injury
Only place the machine on the nut/screw when
switched off.
Battery flat or machine over-
loaded.
Change the battery.
Place the machine under reduced
stress.
Machine is overheating.
You must allow the machine to
cool before using again.
LiIon battery pack is faulty or has
overheated.
Once the battery pack has cooled,
perform a functional check using
the charger.
WARNING
Risk of injury, electric shock
Always disconnect the battery pack from the
machine before any maintenance or care work!
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TI 15-14.4 V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TI 15-14.4 V in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 17,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info