796174
18
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
must be switched off and then switched back on
again.
Due to the built-in restart protection, the power
tool cannot be switched on and off via an exter
nal switch module.
Brake
The OF 1010 REBQ has an electronic brake
which brings the spindle with tool to a standstill
within approx. 2 seconds of the tool being
switched off.
7.2 Changing tools
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
To change tools, place the power tool on its
side.
Inserting the tool
Insert the routing tool into the open collet
as far as possible or at least up to the
mark on the router shank.
Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
Tighten the nut [1-5] using an open ended
spanner (WAF 19).
Removing the tool
Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
Undo the nut [1-5] using an open ended
spanner (WAF 19) until you can feel resist
ance. Overcome the resistance by continu
ing to turn the open ended spanner.
Remove the router.
7.3 Changing the collets
Collets are available for the following shaft di
ameters: 6.0 mm; 6.35 mm; 8.0 mm (See
Festool catalogue or online at www.festool.com
for the order numbers)
Completely unscrew the nut [1-5] and re
move it together with the collet.
Only insert a new collet into the spindle if a
nut is fitted and engaged.
Gently screw in the nut. Do not tighten the
nut if no cutter is inserted.
7.4 Setting the routing depth
The routing depth is set in three steps:
1. Set the zero point, see 7.5.
2. Specify the routing depth, see 7.6.
3. Clamp the routing depth, see 7.7.
7.5 Setting the zero point
Release the clamp lever [1-8] so that the
depth stop [1-3] can move freely.
Position the router with the router ta
ble [1-1] on a level surface. Open the rotary
knob [1-7] and push the power tool down
wards until the cutter sits on the surface.
Clamp the power tool in this position by
closing the rotary knob [1-7].
Press the depth stop [1-3] against one of
the three fixed stops of the rotatable step
ped stop [1-2].
A hex key can be used to individually adjust the
height of each fixed stop.
Push the indicator [1-10] downwards so
that it points to 0 mm on the scale.
If the zero position is incorrect, this can be
corrected using the screw on the indica
tor [1-10].
7.6 Specifying the routing depth
The required routing depth can be specified us
ing either quick depth adjustment or fine depth
adjustment.
Quick depth adjustment
Pull the depth stop [1-3] upwards until the
indicator [1-10] points to the required rout
ing depth.
Clamp the depth stop in this position using
the clamp lever [1-8].
Fine depth adjustment
Clamp the depth stop using the clamp lev
er [1-8].
Set the required routing depth by turning
the adjusting wheel [1-9].
Turning the adjusting wheel by a mark
changes the routing depth by 0.1 mm. A
full rotation changes the routing depth by
1 mm. The maximum adjustment range for
the adjusting wheel is 8 mm.
7.7 Clamping the routing depth
Open the rotary knob [1-7] and push the
power tool down until the depth stop touch
es the fixed stop.
Clamp the power tool in this position by
closing the rotary knob [1-7].
English
18
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool OF 1010 REQ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool OF 1010 REQ in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2.77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info