778534
25
Verklein
Vergroot
Pagina terug
1/164
Pagina verder
8 Working with the electric
power tool
When working on the machine, observe
all of the safety warnings that are listed
at the start as well as the following rules:
Before starting
Do not work with the machine if the elec
tronics are defective, because this may lead
to excessive speeds. You can tell if the
electronics are defective if there is no
smooth start-up or if it is not possible to
regulate the speed or where smoke is
present or if there is a smell of burning
coming from the machine.
Before each use, check that the pendulum
guard is working correctly using the re
tractor lever [1-4]. Ensure that the pendu
lum guard can move freely and does not
come into contact with the saw blade or
other parts at any cutting angle or depth.
Only use this power tool when it is in per
fect working order.
Make sure that the rotary knob [1-13] is
tightened before starting work.
Position the workpiece so that it is stress-
free and level.
Make sure that the extractor hose does not
snag the entire saw cut, either on the work
piece, the workpiece support or hazards on
the ground.
During work
When working, always hold the power tool
with both hands on the handles [1-1]. This
is a prerequisite for precise work and is es
sential for plunge-cutting. Plunge into the
workpiece slowly and evenly.
Only guide the power tool towards the
workpiece when it is switched on.
Always push the saw forwards [7-9], and
never towards yourself.
Adapt the infeed speed to prevent the cut
ters on the saw blade from overheating and
prevent plastic materials from melting dur
ing cutting. The harder the material to be
sawn, the lower the feed speed needs to be.
8.1 Sawing along the scribe mark
The cut indicators display the cutting sequence
without a guide rail:
0° cuts: [6-1]
45° cuts: [6-2]
8.2 Cutting sections
Position the saw with the front part of the saw
table on the workpiece, switch on saw and push
forward in cutting direction.
8.3 Sawing cut-outs (plunge cuts)
In order to avoid kickbacks, the following
instructions must always be followed when
plunge cutting:
Always position saw with the rear edge of
the saw table against a fixed stop.
When working with the guide rail, place the
saw against the kickback stop FS-RSP (ac
cessories) [7-7] clamped to the guide rail.
CAUTION
Danger of crushing
Always keep a firm grip on the machine
with your free hand when adjusting plunge
cuts.
Never position your fingers behind or be
low the saw blade.
Procedure
Adjusting cutting depth, see section 7.2.
Press lever [7-1] down.
Sawing unit swivels upwards to plunge-cut
position.
Hold retractor lever [7-2] downwards as far
as stop.
Pendulum guard [7-5] opens and the saw
blade is exposed.
Position saw on workpiece and position
against a stop (kickback stop).
Switch on saw.
Slowly press down saw to the set cutting
depth until the saw engages, release re
tractor lever [7-2] and push forward in cut
ting direction [7-9].
The notch [7-4] indicates the absolute rear cut
ting point of the saw blade (diameter 160 mm)
when using the saw at maximum cutting depth
with the guide rail.
8.4 Operation with an electric generator
(EG) driven by a combustion engine
Festool cannot guarantee that the power
tool will operate correctly in conjunction
with all EGs.
The power tool can be operated with an EG as
long as the following conditions are fulfilled:
The EG's output voltage must remain in the
range 230 VAC ±10% and the EG must be
English
25
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool HK 85 EB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool HK 85 EB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7.99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info