778622
9
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
1 Symbols
Warning of general danger
Read the operating instructions and
safety instructions.
Do not dispose of it with domestic
waste.
Disconnecting the mains power cable
Tip or advice
Handling instruction
2 Safety warnings
WARNING! Read all safety warnings,
instructions, illustrations and specifica
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Observe the operating manual of the power
tool.
3 Intended use
The AH-ES-ETS/ETSC is intended for sanding
edges in connection with the ETS 125 REQ,
ETSC 125 Li power tools.
The AH-ES-ETS/ETSC must not be used in
conjunction with the ETS 125 EQ power tools or
any orbital sanders/delta sanders (DTS 400,
RTS 400, DTSC 400, RTSC 400).
Do not use the AH-ES-ETS/ETSC with the
ST-STF 125/8-M4-J SW sanding pad. The
larger size of the sanding pad can cause
the abrasive to collide with the base
runner.
4 Parts of the device
[1-1] Sanding mode setting
[1-2] Handle
[1-3] Angle lock rotary knob
[1-4] Angle display
[1-5] Base runner button
[1-6] Base runner
The specified illustrations appear at the begin
ning of the Operating Instructions.
5 Assembly
5.1 AH-ES-ETS/ETSC Assembling on the
power tool [2]
Insert the housing shell [2-2] into the
protector groove [2-3] of the power tool.
Place the counterpart housing shell [2-1]
on top.
Connect the housing shells with the two
enclosed screws and a hex key.
5.2 Calibrating the angle display [3]
The machine has an adjustable angle display.
After first assembling it on your power tool, the
angle display must be calibrated to your power
tool.
Set the sanding mode to "Hard" (see
Section 6.1 ).
Release the angle lock rotary knob [3-3].
Use a measuring tool to set the angle to
90°.
Tighten the angle lock rotary knob.
Loosen the angle calibration locking
screw [3-1].
Move the angle display [3-2] until the
display points to the 90° mark.
Tighten the angle calibration locking screw.
6 Settings
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
6.1 Sanding mode setting
Hard mode [4a]
In Hard mode (setting for pre-sanding), the
edge is sanded according to the set angle.
Soft mode [4b]
In Soft mode (setting for intermediate sanding),
the AH-ES-ETS/ETSC adapts exactly to the
existing surface so that paint or filler is not
sanded through.
6.2 Setting the sanding angle
See figure [5].
English
9
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ES-ETS 125 - 2021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ES-ETS 125 - 2021 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2.35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info