498031
9
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
9
Smooth start-up
The smooth start-up ensures the router starts
up jolt-free.
Constant speed
The pre-selected speed remains constant whether
the machine is in operation or in neutral position.
Temperature control
To prevent overheating, the safety electronics
switches the machine off when it reaches a critical
motor temperature. Let the machine cool down
for approx. 3-5 minutes before using it again. The
machine requires less time to cool down if it is
running, i.e. in neutral position.
5 Chip thickness adjustment
The planing depth can be adjusted by turning the
rotary knob (2.1) (turn to the right = larger planing
depth, turn to the left = smaller planing depth).
The planing depth which has been set can be read
at the mark (2.3) for the rotary knob scale (2.2).
Adjustment by one scale mark corresponds to a
change in planing depth of 0.1 mm.
The max. planing depth is 4 mm. So as no to
overload the machine, we recommend that a
maximum planing depth of 2.5 mm be set with a
plane width > 40 mm.
6 Changing cutters
Use only cutters which are sharp and
undamaged. Blunt cutters increase the
danger of kick-back and reduce the plan-
ing quality obtained.
- Always disconnect the mains plug from the
socket before changing the cutter.
- Loosen the locking screw (2.9) by approx. 2
revolutions with the Allan key (2.6) and remove
the cutter from the cutter shaft.
- Clean the cutter slot before inserting the new
cutter to ensure a correct fi t.
- Then insert the new cutter (488 503) into the
groove with the printed side facing the rear
planer platen (2.8).
- Before tightening the locking screws (2.9) align
the cutter with a ruler so that its front edge
(1.13) is fl ush with the sides of the front (1.12)
and rear (1.14) planer platens. Then tighten fi rst
the central locking screw, followed by the two
outer screws.
7 Dust extraction
The standard equipment for the planer
includes devices to enable the planer to
be used with both the chip collecting bag
(1.1) (accessories) (488 566) or a suction
hose (1.2) (accessories) connected to a
dust extractor.
The connector for dust extraction can be fi tted
on either side of the tool. To change sides, press
the toggle lever (1.11) down fi rmly. This releases
the lug on the outer edge of the casing and the
adapter (1.4) can be pushed through the casing
(Fig. 3). The adapter (1.4) can now be inserted
into the casing opening (4.1) lug fi rst up the stop
in the casing.
Either the chip collecting bag (1.1) or an angle
piece (1.3) for a suction hose adapter (1.2) can be
tted to the adapter (1.4). The chips can be de-
ected in any direction by turning the angle piece.
A suction hose Ø 27 mm adapter is inserted into
the angle piece (1.3). A suction hose Ø 36 mm
adapter is fi tted over the angle piece (1.3).
8 Putting the planer down
When working with electric planers you must
remember that the planer shaft continues to run
for a few seconds after the tool is switched off.
The EHL 65 E has a support foot (2.7) at the end
of the platen so that it can be placed safely on a
work surface. If the electric tool is taken up, the
support foot automatically protrudes beyond the
planer platen to ensure that the planer shaft is
always raised above fl at work surfaces when the
planer is put down.
Pay attention to the following when put-
ting the EHL 65 E down:
- check that the support foot is present and fully
operational,
- wait until the planer shaft comes to a standstill
before putting the tool down.
If the support foot should be found obstructive
during special planing work it can be swung back
out of the way and locked in position.
9 Fitting the guides
9.1 Rebating depth guide (488 543)
The rebating depth guide (1.8) is mounted in the
threaded hole (1.10) on the front right of the ma-
chine.
The stop can be infi nitely adjusted to between
0 and 23 mm in accordance with the scale. The
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool EHL 65 E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool EHL 65 E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info