574904
15
Verklein
Vergroot
Pagina terug
1/86
Pagina verder
15
b) Changing tools
- To insert or remove a tool with CENTROTEC
shaft, pull the green release ring (2.10)
back. On inserting the tool, turn it until its
hex shank arbour (2.9) locks in place in the
hexagonal shank of the drill spindle, and
push the tool into the toolholder as far as
it will go.
3.5 Tool holding xture in the drill
spindle
Bits can be tted directly in the hexagon
socket holder of the drill spindle (2.5) to
make the machine lighter and shorter.
4 Charge battery pack
To load the battery pack, push it into the
holder (3.1) on the charger up to the stop.
Perform this in reverse to remove the battery
pack from the charger. The battery type used
(NiCd or NiMH) is detected automatically.
Charging is controlled by a microprocessor.
If a warm NiMH battery pack (>37° C) is
inserted, charging will only be carried out
at a lower charge current. In this case, the
charging time is extended.
The LED (3.2) indicates the respective
charging state of the charger.
LED yellow – steady:
Charger is ready for use.
LED green – ashing:
Battery pack being charged.
LED green – steady:
Battery pack fully charged, conservation
charge on.
LED red – ashing:
General malfunction, e. g. full contact not
being made, short-circuit, battery pack
faulty.
LED red – steady:
Temperature of battery pack is outside
permissible limit.
It is essential that you read
the instructions in the Chapter
„Working instructions - Mainte-
nance - Care“.
5 Working with the machine
5.1 Initial operation
Turn on by pressing button (1.3). Depending
on the pressure exerted on the button, the
adjustment of running speed can be varied
in nitely. Turn off by releasing the button
(1.3).
After releasing the button, the chuck is
stopped and therefore, after-running of the
equipment is prevented.
5.2 Bit storage well
You can insert several bits or bit extensions
into the bit magazine (1.2) with magnetic
holder.
5.3 Warning signal
With the following operational statuses, the
machine sounds an acoustic warning signal
and switches off:
Peep at regular intervals
- Battery empty
Triple peep at regular intervals
- Excessive load (torque)
- Machine too warm.
6 lnstructions on application -
maintenance - care
Please pay attention to the fol-
lowing instructions. Otherwise
there is a risk of damage to the
tool, charger or battery pack.
- Repairs may only be performed by author-
ised technicians. LC 45 charging device:
Even after disconnection from the mains,
there is still a high capacitor voltage on the
power output component on the inside of
the device.
- Keep the air vents of the electronic equip-
ment and the charger clean to guarantee
the air circulation for cooling.
- No metal objects (metal chips) should
enter the charger at the contact points as
well as through the cooling slits into the
equipment (danger of short circuit).
- Only use original Festool battery packs.
Do not use spent and recycled battery
packs. The user shall be liable for dam-
ages if Festool original battery packs are
not used.
- Keep the connection contacts of electronic
equipment, charger and battery pack
clean.
- By keeping the battery pack in a ready for
use charger, the battery pack will be kept
in a state of readiness by oat charging
conservation.
- Do not keep discharged battery pack
(maximum one month) attached to charger
whenever charger is detached from the
15

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Festool-C12-12.0-V

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool C12-12.0 V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool C12-12.0 V in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info