778636
14
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Accessories shown or described are not always
included in the scope of delivery.
The specified illustrations appear at the begin
ning of the Operating Instructions.
6 Commissioning
WARNING
Unauthorised voltage or frequency.
Risk of accidents
Observe the specifications on the ma
chine's name plate.
Observe country-specific regulations.
6.1 Changing the battery pack
Inserting the battery pack [2 A]
Removing the battery pack [2 B]
6.2 Lighting and battery capacity indicator
The LED [1-10] provides light and acts as
a battery capacity indicator [1-9].
When the on/off switch [1-4] is pressed, the
LED automatically displays the state of charge
of the battery pack (not for NiCd and NiMH bat
tery packs).
Green LED – steady light:
State of charge > 60%
Green LED – flashing
slowly: State of charge
30%–60%
Green LED – flashing
quickly: State of charge
0%–30%
Yellow LED – steady light:
Battery is flat
Red LED – steady light:
Temperature of the bat
tery, electronics or motor
is outside the permitted
range.
Red LED – flashing: Gen
eral fault indicator, e.g. not
in full contact, short cir
cuit, faulty battery pack,
etc.
When the battery pack is empty, or if there
is a power failure or the mains plug is re
moved, move the on/off switch immediate
ly to the Off position. This prevents uncon
trolled restarting.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
7 Settings
7.1 Changing direction of rotation [1-3]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
7.2 Selecting the operating mode
Hammer drilling
Set selector switch [1-5] to hammer
symbol.
Screwdriving/drilling
Set selector switch [1-5] to drill symbol.
8 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
8.1 Changing tools [3]
Drills are clamped by means of the SDS-
plus system without using a wrench.
CAUTION
Hot and sharp tools
Risk of injury
Do not use any blunt or defective insert
tools.
Wear protective gloves.
Inserting the tool
Clean the tool shank and apply a coating of
multipurpose grease.
Do [1-2] not retract the release sleeve, but
insert the tool in the tool holder [1-1] and
turn until it engages.
Check that the tool is seated correctly.
Removing the tool
Push the unlocking sleeve [1-2] back and
remove the tool.
8.2 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CEN
TROTEC tool chucks.
English
14
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool BHC 18 Li - 2021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool BHC 18 Li - 2021 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3.25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info