778628
24
Verklein
Vergroot
Pagina terug
1/146
Pagina verder
8.1 Fitting the auxiliary handle [1-6]
Always use the auxiliary handle to ensure
a safe working posture that prevents you
from tiring.
The special "VIBRASTOP" design of the auxiliary
handle helps to reduce vibrations.
Screw in the auxiliary handle [1-6] on the
side of the thread [1-3] according to the
working method.
8.2 Fitting the sanding tool [4]
CAUTION
Risk of injury from hot and sharp tool
Do not use any vibrating, blunt or defective
sanding tools.
Do not use sanding tools that have been
exposed to extreme humidity, moisture or
high temperatures prior to installation.
Wear protective gloves.
WARNING
Risk of injury from incorrectly fitted sanding
tool
Only fold up the lift-up handle [4-3] for the
quick-action clamping nut when you are
replacing the sanding tool.
Ensure that the flange [4-4] is fitted on the
spindle before installing the sanding tool.
Only tighten or loosen the clamping nut by
hand. Never use tools to loosen or tighten
the lift-up handle.
If the nut can no longer be loosened by
hand, it should only be loosened with a
face wrench [5-1].
If the lift-up handle is loose or damaged,
the clamping nut must no longer be used
under any circumstances.
Use the guard provided for the application
in each case.
Remove the battery pack from the power
tool.
Open the lift-up handle [4-3] for the quick-
action clamping nut.
Unscrew the quick-action clamping nut
[4-2] by hand.
Place the sanding tool on the spindle
and flange [4-4].
Ensure that the centring ridge of the flange
fits exactly into the opening in the disc and
that the form-fit connection between the
power tool/spindle and flange matches.
Ensure that the diameter of the power tool
spindle matches the hole in the sanding
tool.
Offset sanding tools must be fitted so
that their sanding area does not pro
trude beyond the edge of the guard.
Adhere to the stipulated rotational direction
of the sanding tool (arrow on the sanding
tool = arrow on the tool housing [4-1]).
Place the quick-action clamping nut on the
sanding tool and spindle.
Press the spindle lock [4-5] on the re
verse of the tool.
Tighten the quick-action clamping nut by
hand.
Close the lift-up handle for the quick-ac
tion clamping nut.
Check that the sanding tool is securely at
tached and fitted to the power tool.
Let new sanding tools run for around one
minute with no load as a test.
Removal is performed in reverse sequence to
assembly [5a].
8.3 Fitting the wire brushes [6]
Remove the handle [6-1].
Fit the handle with hand protection
[6-2].
Fit the wire brushes [6-3] securely in the
holding thread [6-4].
Observe the information provided for the
wire brushes.
8.4 Positioning the guard/cutting guard [7]
The guard is preassembled. You can simply
turn the guard to adapt its position to the re
quirements of the task.
Press and hold the locking lever on the
guard.
Adjust the guard on the power tool so
that sparks and particles are deflected away
from the body.
Release the locking lever and continue
to turn the guard until it locks in place.
The cutting guard, available as an acces
sory, can be positioned in the same way.
English
24
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool AGC 18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool AGC 18 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3.53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info