724593
11
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
concrete, fencing, wire, wood, metal, etc.
Never use blades near footpaths, fencing, posts, buildings or other
immovable objects.
Never use a blade after hitting a hard object without rst inspecting
it for damage. Do not use if any damage is detected.
The unit is used as a scythe, cutting from the right to the left in a
broad sweeping action from side to side.
Always wear goggles, earmus and a dust mask when using the
Brushcutter.
Only use blades with a cutting diameter of 255mm and a bore size
of 25.4 mm.
Only use the Brushcutter with the correctly supplied and tted
Brushcutter guard.
Keep bystanders a minimum of 15 metres from the operation of the
Brushcutter.
Prior to operation, ensure the assembled Brushcutter is checked for
loose components and the operating controls of the Brushcutter.
Do not use the Brushcutter if the controls are not in perfect working
order. Ensure all nuts, bolts and clamps are all tight.
Check the blade is correctly seated and the blade nut is tight.
DO NOT substitute the blade with any other types of blade other than
that is detailed in this manual. DO NOT t a saw blade to this product.
This brushcutter is tted with a centrifugal clutch. At idle, the blade
must not be rotating. Make a practice to always check the clutch is
correctly operating and at idle the blade does not rotate, and rotation
of the blade only occurs as the speed of the motor is increase from
manually operating the speed trigger.
Do NOT use the brushcutter if the blade at idle speed is rotating and
take it to an authorised service centre.
Exercise extreme caution when using the 3T brushcutter blade with
this unit. Blade thrust is the reaction which may occur when the
spinning 3T brushcutter blade contacts anything it cannot cut.
This contact may cause the 3T brushcutter blade to stop for an instant,
and suddenly “thrust the unit away from the object that was hit.
This reaction can be violent enough to cause the operator to lose
control of the unit. Blade thrust may occur without warning if the
blade snags, stalls or binds. This is more then likely to occur in areas
where it is dicult to see the material being cut.
9
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferrex SBC52 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferrex SBC52 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info