Wall chaser FWS-150K
14
Wall chaser FWS-150K
3
Caution!
Whenever working with electric tools, always take
basic safety precautions including those described
below, to reduce the risk of fire, electric shock, and
personal injury.
Before using the product, read all safe use directions
and keep them in a handy place.
Directions for safe use:
1 Keep the working environment tidy
• Untidy workplaces and benches can easily cause
accidents.
2 Be alert to the conditions in your surroundings.
• Do not expose electric tools to rainwater.
•Never use electric tools in damp or wet condi-
tions.
• Ensure that the work area is well lit.
•Never use electric tools where there is a hazard of
combustion or explosion.
3 Protect yourself from electric shock
•Avoid bodily contact with earthed surfaces (such
as pipes, radiators, heaters, refrigerators).
4 Keep children at a safe distance
• Do not allow bystanders to touch the tool or ex-
tension cord.
• Do not allow bystanders access to the worksite.
5 Store tools, which are not in use
• Store tools, which are not in use, in a dry, high, or
lockable place, beyond the reach of children.
6 Do not overload the tool
• For a good and safe result, use the tool settings
advised.
7 Use the right tool for the job
• Do not use light tools or accessories for heavy du-
ty jobs.
• Never use the tool for work it was not designed to
do. For example, do not use a circular saw to saw
branches or cut down trees.
8 Wear suitable work clothing
•Wear no loose clothing or jewellery, as these
could become entangled in moving parts of the
machine.
• When working outdoors, rubber gloves and foot-
wear with heavy profile soles are recommended.
•Wear a headband or hairnet to keep long hair out
of the danger zone.
9 Wear safety glasses
• When your work generates dust, wear a dustmask
or facemask.
10 Connect a dust extraction system
• If the tool provides for connection to a dust
extraction system, ensure that this is connected
and working correctly.
11 Only use the power cord for its intended use
• Never carry the tool by its power cord, and do not
unplug the tool from the power by pulling on the
power cord.
•Protect the power cord from heat, oil, and/or
sharp edges.
12 Do not overextend yourself
• Ensure you have secure footing, and maintain
your balance at all times.
13 Maintain the tool with care
• Keep cutting equipment sharp and clean, so you
will achieve a good result, safely.
• Follow the directions for lubrication and replace-
ment of parts.
• Inspect the power cord regularly and have a da-
maged cord repaired by an authorised service
agent.
• Inspect extension cords regularly, and replace
any damaged cords.
•Keep handgrips dry, clean and free from grease
and oil.
14 Remove the plug from the wall socket
•Whenever the tool is not in use, and before ex-
changing parts such as blades, bits and knives.
GENERAL SAFETY INSTRUCTIONS
1. Maintain the tool with care.
• Keep the tool clean and sharp.
• Follow the directions for lubrication and fitting of
accessories.
• Periodically inspect the power cord, and have any
damage repaired by an authorised service agent.
• Periodically inspect extension cords, and replace
them if damaged.
• Keep handgrips dry, clean and free from grease
and oil.
2. Always remove the plug from the mains, whene-
ver:
• the machine is not in use;
• you service the machine;
• exchanging accessories such as blades.
3. Immediately repair any damage.
Regularly inspect all moving parts, attachments
and all other parts that can affect correct opera-
tion.
• Have all repair work carried out by an authorised
service agent.
MAITENANCE AND REPAIR
MAITENANCE AND REPAIR
Malfunctions
Problem
The electric motor becomes hot
and cuts out.
The machine switched will not
run.
Cutting is difficult and the channel
made is irregular.
When cutting, the workpiece be-
gins to vibrate heavily
The machine runs erratically
and/or noisily.
Possible cause
The overheating protection has been
activated.
The motor is defective.
The overload protection has been acti-
vated.
The overheating protection has been
activated.
The switch is damaged.
The cutting discs are bent or blunt.
The cutting discs are overheated or de-
formed.
The carbon brushes are worn.
Solution
Wait several minutes until the machi-
ne has cooled down, then re-start the
machine.
Take the machine to your Ferm dealer
for inspection and/or repair
Re-start the machine.
Wait several minutes until the machi-
ne has cooled down, and then re-
start the machine.
Take the machine to your Ferm dealer
for inspection and/or repair
Replace the cutting discs.
Replace the cutting discs.
Take the machine to your Ferm dealer
for replacement of the carbon brush-
es.
