30 Ferm
BELT SANDER
TECHNICAL SPECIFICATIONS
PRODUCTINFORMATION
Fig. A
The belt sander is the perfect tool to sand wood and to
grind iron, plastic or similar materials.
The belt sander must be used for the rough work, for the
normal sanding work an orbital sander must be used.
1. On/off switch
2. Front handle
3. Rear handle
4. Blocking switch
5. Dust collection opening
6 Adjusting knob
7. Sanding belt fastener
8. Front belt roller
9. Direction indicator
10. Drive belt cover
11. Dust bag
PACKAGE CONTENTS
1 Belt sander
3 Sanding belts
1 Dust collection bag
1 Instruction manual
1 Safety instructions
1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
ELECTRICAL SAFETY
Always check that the power supply corresponds
with the voltage on the rating plate.
The machine is double insulated in accordance
with EN-50144; therefore no earth wire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY PRECAUTIONS
• If you are working with the sanding machine, wear
always ear protectors and dust mask.
• The sanding machine is not suitable for wet sanding.
• Check if the switch is not in position “ON”, before
you connect the mains plug to the mains voltage.
• Keep the mains lead always away from moving parts
of the tools.
• Use safety glasses, especially when you sand above
your head.
• Do not bring pressure to your machine, this will only
delay the sanding.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or mains
lead damage.
• Defect switch
• Smoke or stench of scorched isolation
Voltage | 230 V~
Frequency | 50 Hz
Power input | 800 W
No load sander paper speed | 280 m/min
Sanding belt size | 75 x 533 mm
Sanding pad size | 75 x 160 mm
Weight | 3.0 kg
Lpa (Sound pressure) | 88.6 dB(A)
Lwa (Sound power level) | 101.6 dB(A)
Vibration value | 3.511 m/s
2
Ferm 3
SPARE PARTS LIST FBS-800
REF NR DESCRIPTION FERM NR
01 +02 CARBON BRUSH HOLDER 409000
03 + 04 CARBON BRUSH SET 409001
05 BELT WHEEL 409002
06 BEARING 608-2Z 800608
08 ROTOR 409003
16 STATOR 409004
17 BEARING 626-2Z 800626
21 + 50 NEEDLE BEARING HK081210 801211
22 SPINDLE 409005
23 ROLL 409006
26 SWITCH 409007
31 BASE PLATE 409008
41 BELT WHEEL 409009
43 + 45 BEARING 627-2Z 800627
44 SPIRAL GEAR 409010
47 BIG GEAR 709011
53 DRUM 409012
55 ADJUSTING KNOB 409013
73 BELT COVER 409014
67 + 68 DUSTBAG COMPLETE 409015
61 DRIVING BELT 409016
