510127
8
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
8
EN
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Alwaysusesharpsawblades.
• Donotsawtoosmallworkpieces.
• Neverreleasetheworkpiecebeforeithas
been completely pushed through the saw.
• Alwaysadjusttheguideparalleltothesaw
blade.
• Neverremovethesawprotection.
36. Before you continue sawing, ensure that you
are standing rmly and that your hands are in
the required position.
37. Never use thinners to clean the machine. Only
use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or
deformed.
39. Replace table insert when worn.
40. Use only saw blades recommended by the
manufacturer.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect circular saws to a dust-collecting
device when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45. Take care when slotting.
Before use, remove the transport protection:
Disassemble the bottom plate by loosening the
4 screws.
Remove the transport protection below motor.
The handles for height and mitre setting of the
saw blade are located in the transport
protection inside the machine.
Reassemble the bottom plate.
Switch off the machine immediately when you
discover:
A defective mains plug or mains lead.
A defective switch.
Overheating of the machine.
Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of re, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Alwayscheckthatthepowersupply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm
2
and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
Only connect your machine and/or extension
cable to an earthed electricity mains.
This machine can be switched to the single-
phase network (230 V/50 Hz). If you are in
doubt about the earth of the electricity
provisions, consult an electrician rst.
3. ASSEMBLY INSTRUCTIONS
Installation of the machine on a workbench or
on the subframe
This machine is a stationary machine and for
safety reasons must always be rmly installed
and not used for mobile applications.
You can install the machine in two ways:
a. As a stationary machine on a workbench. In
this case the machine must be secured to the
workbench with 4 bolts.
b. As a stationary machine on the subframe. In
this case the machine must be secured to the
subframe with 4 bolts and the subframe
anchored to the oor or to a oor plate with
dimensions of at least 1 square metre
Assembly of the bench saw on the workbench
Fig. B & C
Before adjusting the saw, make sure the
plug is removed from the socket.
Fig. B shows the distance of the holes to be
drilled in the workbench on which to fasten the
machine. Drill holes of 8 mm.
Only use the machine after it has been
assembled completely and it has been
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-TSM1030

Zoeken resetten

  • Is deze machine met dit zaagblad geschikt voor het zagen van laminaat en of PVC vloerdelen??
    Is het ook geschikt voor het in verstek zagen van hoge plinten ( 12CM hoog)??
    Gesteld op 4-10-2020 om 19:47

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TSM1030 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TSM1030 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info