539202
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Ferm6
GB
Speed control
Fig. I
• Duringoperationandwhilstthemachine
is at rest the stroke rate (speed) can be
selected using the thumbwheel (6).
• Thestrokeraterequireddependsuponthe
material conditions. The optimal setting
should be determined in use.
• Afterworkingforlongerperiodsatlow
speed you should allow the machine to cool
down by running it at maximum speed with
no-load for approx. 3 minutes.
Sawing tips
• Adjustsawbladeandstrokeratetosuitthe
material to be processed. For right radius
curves it is best to use a narrow saw blade.
Apply coolant or lubricant to deal with the
utteringproducedalongthecutlinewhen
sawing metal.
• Checkwood,chipboards,building
materials etc, for foreign bodies (nails,
screws etc.), before sawing and remove
them, if necessary.
• Clampmaterialwell.Donotsupportthe
workpiece with hand or foot. Do not touch
objectsortheoorwiththesawrunning
(danger of backlash).
• Putthefootplateonthesurfaceofthe
workpiece, and saw through it with constant
contactpressureorfeed.Ifthesawblade
seizes switch the machine off immediately.
Spread the gap with a suitable tool and pull
out the saw blade.
• Afternishingwork,switchoffthemachine
and only put down after it has come to a
complete standstill.
Plunge cutting
Fig. E
• Plungecuttingmayonlybeusedonsoft
materials such as wood, aerated concrete,
gypsum plaster boards, etc.
• However,thisrequiresacertainpractise
and is only possible with short saw blades.
• Placethesawontotheworkpieceand
switch it on.
• Ensurethatthebottomedgeofthefootplate
rests on the workpiece surface as shown.
• Slowlysawintotheworkpieceatanangle,
moving the saw to a vertical position and
continue to saw along the cutting line.
• Switchthesawoffandliftofftheworkpiece
when the work is complete.
Flush sawing
• Elasticbi-metalsawbladesallowyouto
saw protruding objects (e,g, water pipes,
iron bars, etc,) nearby the wall.
• Applythesawbladedirectlytothewall
and bend slightly so that the footplate rests
against the wall.
• Switchthemachineonandsawoffthe
workpiece keeping constant lateral pressure
against the wall.
Rotatable handle
Fig. F
The handle can be rotated in 90° steps to the
machine housing. Slide the rotation button (3)
backwards and rotate the handle to the desired
position. Make sure the handle locks in position
before use.
LCD display
Fig. G
This machine is equipped with a LCD display.
• Toturnthedisplayon,pressthedisplay
button (10) once. To turn the display off,
press the display button again.
• Theclock(11)andminutes(12)remaining
icons indicate the number of minutes of
running time that are available before the
batteryrequiresrecharging(Lithium-Ion
battery only)
• Thebatteryicon(13)indicatesthe
amount of charge remaining in the battery.
Each charge bar displayed indicates
approximately 10% charge remaining in the
battery. A total of 10 charge bars indicates a
fully charged battery.
• Pressthebacklightbutton(14)toswitchthe
backlightofthedisplayon.Pressitagainto
switch the backlight of the display off.
Hex key storage
Fig. H
The included hex key can be stored in the
battery compartment.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work
on the motor.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm RSM1014 FPRS-1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm RSM1014 FPRS-1800 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info