ADJUSTING THE FOOT PLATE ANGLE
Fig.D
•To allow the foot plate to follow and securely rest on
the workpiece, the angle of the footplate can be
adjusted as shown in the diagram.
•The footplate can also be extended by loosening the
two footplate length adjustment screws (Fig. A8)
using the 4 mm hexagon key and then pulling the foot-
plate out to the required length.
Ensure the footplate adjustment screws are secure
before resuming work.
SAWING TIPS
•Adjust saw blade and stroke rate to suit the material
to be processed. For right radius curves it is best to
use a narrow saw blade. Apply coolant or lubricant to
deal with the beat produced along the cut line when
sawing metal.
•Check wood, chip boards, building materials etc, for
foreign bodies (nails, screws etc.), before sawing and
remove them, if necessary.
•Clamp material well. Do not support the workpiece
with hand or foot. Do not touch objects or the floor
with the saw running (danger of backlash).
•Material containing asbestos must not be sawn!
•Put the footplate on the surface of the workpiece,
and saw through it with constant contact pressure or
feed. If the saw blade seizes switch the machine off
immediately . Spread the gap with a suitable tool and
pull out the saw blade.
•After finishing work, switch off the machine and only
put down after it has come to a complete standstill.
PLUNGE CUTTING
Fig.E
•Plunge cutting may only be used on soft materials
such as wood, aerated concrete, gypsum plaster
boards, etc.
•However, this requires a certain practise and is only
possible with short saw blades.
•Place the saw onto the workpiece and switch it on.
•Ensure that the bottom edge of the footplate rests on
the workpiece surface as shown.
•Slowly saw into the workpiece at an angle, moving the
saw to a vertical position and continue to saw along
the cutting line.
•Switch the saw off and lift off the workpiece when the
work is complete.
FLUSH SAWING
•Elastic bi-metal saw blades allow you to saw projec-
ting objects (e,g, water pipes, iron bars, etc,) flush
against the wall.
•Apply the saw blade directly to the wall and bend
slightly so that the footplate rests against the wall.
•Switch the machine on and saw off the workpiece
keeping constant lateral pressure against the wall.
There are no user servicable parts in this unit. Any
repairs or servicing should be carried out by qualified
service en-gineers.
TROUBLESHOOTING
In case the machine does not work well, we give you
some possible causes and solutions.
1. The electromotor gets hot
•The cool ventilation slots in the motor are stopped
up with dirt.
Clean the cool ventilation slots.
•The motor is defect.
Have your machine repaired or checked by your local
Ferm dealer.
2. The connected machine does not work
•Interruption in the mains connection.
Check mains connection for fracture.
Have your machine repaired/checked by your local
Ferm dealer.
Repairing of electric appliances may be carried out
only by experts.
MAINTENANCE
Make sure that the machine is not live when car-
rying out maintenance work on the motor.
The Ferm machines have been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon pro-
per machine care and regular cleaning.
Cleaning
Keep the ventilation slots of the machine clean to pre-
vent overheating of the engine.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.
If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol,
alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please con-
tact your local Ferm dealer.
In the back of this manual you find an exploded view
showing the parts that can be ordered.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations.
Take your unwanted machines to your local Ferm-
dealer. Here they will be disposed of in an environmen-
tally safe way.
Ferm 5
ìëíêÄçÖçàÖ çÖèéãÄÑéä
凯Ë̇ Ì ËÏÂÂÚ ˜‡ÒÚÂÈ, ÍÓÚÓ˚È ÏÓÊÂÚ
ÂÏÓÌÚËÓ‚‡Ú¸ ‚·‰ÂΈ. êÂÏÓÌÚ Ë ÚÂıÌ˘ÂÒÍÓÂ
Ó·ÒÎÛÊË‚‡ÌË ‰ÓÎÊÌ˚ ‚˚ÔÓÎÌflÚ¸Òfl
Í‚‡ÎËÙˈËÓ‚‡ÌÌ˚Ï Ò‚ËÒÌ˚Ï ÔÂÒÓ̇ÎÓÏ.
çËÊ ÔË‚Ó‰ËÚÒfl fl‰ ÌÂÔÓ·‰ÓÍ, Ëı ‚ÓÁÏÓÊÌ˚Â
Ô˘ËÌ˚ Ë ÏÂÚÓ‰˚ ÛÒÚ‡ÌÂÌËfl.
1. ùÎÂÍÚÓ‰‚Ë„‡ÚÂθ Ô„‚‡ÂÚÒfl
•ÇÂÌÚËÎflˆËÓÌÌ˚ ˘ÂÎË ‰Îfl Óı·ʉÂÌËfl Á‡·ËÎËÒ¸
„flÁ¸˛.
èÓ˜ËÒÚËÚ¸ ‚ÂÌÚËÎflˆËÓÌÌ˚ ˘ÂÎË.
•ùÎÂÍÚÓ‰‚Ë„‡ÚÂθ ÌÂËÒÔ‡‚ÂÌ.
é·‡ÚËÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm ‰Îfl
ÓÒÏÓÚ‡ ËÎË ÂÏÓÌÚ‡.
2. ëÓ‰ËÌÂÌ̇fl Ò ÒÂÚ¸˛ χ¯Ë̇ Ì ‡·ÓÚ‡ÂÚ
•é·˚‚ ‚ ÒÓ‰ËÌÂÌËË Ò ÒÂÚ¸˛.
èÓ‚ÂËÚ¸ ÒÓ‰ËÌÂÌËÂ Ò ÒÂÚ¸˛ ̇ Ó·˚‚.
é·‡ÚËÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm ‰Îfl
ÓÒÏÓÚ‡ ËÎË ÂÏÓÌÚ‡.
êÂÏÓÌÚ ˝ÎÂÍÚ˘ÂÒÍËı ÔË·ÓÓ‚ ‰ÓÎÊÂÌ
‚˚ÔÓÎÌflÚ¸Òfl ÚÓθÍÓ ÒÔˆˇÎËÒÚ‡ÏË.
íÖïçàóÖëäéÖ
éÅëãìÜàÇÄçàÖ
ÇÒ„‰‡ ÓÚÍβ˜‡ÈÚ χ¯ËÌÛ ÓÚ ÒÂÚË Ô‰
‚˚ÔÓÎÌÂÌËÂÏ ÚÂıÌ˘ÂÒÍÓ„Ó Ó·ÒÎÛÊË‚‡ÌËfl
˝ÎÂÍÚÓ‰‚Ë„‡ÚÂÎfl.
凯Ë̇ ‡ÒÒ˜Ëڇ̇ ̇ ‰ÎËÚÂθÌÛ˛ ‡·ÓÚÛ Ò
ÏËÌËχθÌ˚Ï Ó·˙ÂÏÓÏ ÚÂıÌ˘ÂÒÍÓ„Ó Ó·ÒÎÛÊË‚‡ÌËfl.
ê„ÛÎfl̇fl ˜ËÒÚ͇ Ë Ô‡‚ËθÌÓ ӷ‡˘ÂÌËÂ
Û‚Â΢˂‡˛Ú ÒÓÍ ÒÎÛÊ·˚ χ¯ËÌ˚.
óËÒÚ͇
ëÓ‰ÂÊËÚ ‚ÂÌÚËÎflˆËÓÌÌ˚ ˘ÂÎË ˜ËÒÚ˚ÏË ‰Îfl
Ô‰ÓÚ‚‡˘ÂÌËfl Ô„‚‡.
ê„ÛÎflÌÓ ÔÓÚˇÈÚ χ¯ËÌÛ Ïfl„ÍÓÈ Ú̸͇˛,
Ê·ÚÂθÌÓ ÔÓÒÎÂ Í‡Ê‰Ó„Ó ËÒÔÓθÁÓ‚‡ÌËfl. 쉇ÎflÈÚÂ
Ô˚θ Ë ‰Û„Ë ÓÚÎÓÊÂÌËfl ËÁ ‚ÂÌÚËÎflˆËÓÌÌ˚ı ˘ÂÎÂÈ.
ëÚÓÈÍË Á‡„flÁÌÂÌËfl Û‰‡ÎflÈÚ Ïfl„ÍÓÈ Ú̸͇,
ÒÏÓ˜ÂÌÌÓÈ ‚ Ï˚θÌÓÈ ‚Ó‰Â. ê‡ÒÚ‚ÓËÚÂÎË (·ÂÌÁËÌ,
ÒÔËÚ, ‡ÏÏË‡Í Ë Ú. ‰.) ÔËÏÂÌflÚ¸ Á‡Ô¢‡ÂÚÒfl, Ú. Í.
ÓÌË ÏÓ„ÛÚ Ôӂ‰ËÚ¸ Ô·ÒÚχÒÒÓ‚˚ ‰ÂÚ‡ÎË.
ëχÁ͇
凯Ë̇ Ì Ú·ÛÂÚ ÒχÁÍË.
çÂËÒÔ‡‚ÌÓÒÚË
Ç ÒÎÛ˜‡Â ÌÂËÒÔ‡‚ÌÓÒÚË, ̇ÔËÏÂ, ‚ÒΉÒÚ‚ËÂ
ËÁÌÓÒ‡ ‰ÂÚ‡ÎË, Ó·‡˘‡ÈÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm.
Ç ÍÓ̈ ̇ÒÚÓfl˘Â„Ó ÛÍÓ‚Ó‰ÒÚ‚‡ ËÏÂÂÚÒfl
ËÎβÒÚ‡ˆËfl ÒÓÒÚ‡‚‡ χ¯ËÌ˚, ÔÓ͇Á˚‚‡˛˘‡fl
‰ÂÚ‡ÎË, ÍÓÚÓ˚ ÏÓ„ÛÚ ·˚Ú¸ Á‡Í‡Á‡Ì˚.
áÄôàíÄ éäêìÜÄûôÖâ ëêÖÑõ
ÑÎfl Ô‰ÓÚ‚‡˘ÂÌËfl ÔÓ‚ÂʉÂÌËfl ‚Ó ‚ÂÏfl
Ú‡ÌÒÔÓÚËÓ‚ÍË Ï‡¯Ë̇ ÔÓÒÚ‡‚ÎflÂÚÒfl ‚ ÔÓ˜ÌÓÈ
ÛÔ‡ÍÓ‚ÍÂ. ÅÓθ¯ËÌÒÚ‚Ó ˝ÚËı ÛÔ‡ÍÓ‚Ó˜Ì˚ı
χÚ¡ÎÓ‚ ÏÓ„ÛÚ ·˚Ú¸ ÛÚËÎËÁËÓ‚‡Ì˚. èÓÒËÏ
Ò‰‡Ú¸ Ëı ‚ ÔÛÌÍÚ˚ ÔËÂχ ‚ÚÓ˘ÌÓ„Ó Ò˚¸fl.
ëÚ‡‚¯ËÈ ÌÂÌÛÊÌ˚Ï ËÌÒÚÛÏÂÌÚ ÔÓÒËÏ Ò‰‡Ú¸
ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm. éÌ ·Û‰ÂÚ ÛÚËÎËÁËÓ‚‡Ì
˝ÍÓÎӄ˘Ì˚Ï ÏÂÚÓ‰ÓÏ.
ÉÄêÄçíàü
ìÒÎÓ‚Ëfl „‡‡ÌÚËË ÒÓ‰ÂʇÚÒfl ‚ ÓÚ‰ÂθÌÓÈ
„‡‡ÌÚËÈÌÓÈ Í‡ÚÓ˜ÍÂ.
àÁ„ÓÚÓ‚ËÚÂθ Á‡fl‚ÎflÂÚ, ˜ÚÓ ·ÂÂÚ Ì‡ Ò·fl
ËÒÍβ˜ËÚÂθÌÛ˛ ÓÚ‚ÂÚÒÚ‚ÂÌÌÓÒÚ¸ ‚ ÚÓÏ, ˜ÚÓ ËÁ‰ÂÎËÂ
ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ ÒÎÂ‰Û˛˘ËÏ Òڇ̉‡Ú‡Ï ËÎË
ÌÓχÚË‚Ì˚Ï ‰ÓÍÛÏÂÌÚ‡Ï
EN50144-1, EN50144-2-11, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
Ë Ú·ӂ‡ÌËflÏ ‰ËÂÍÚË‚.
89/392/EEC,
73/23/EEC,
89/336/EEC
ÓÚ 04-12-2002
ÉÂÌÂÏÓȉÂÌ,
çˉ·̉˚
W. Kamphof
éÚ‰ÂÎ ÍÓÌÚÓÎfl ͇˜ÂÒÚ‚‡
CE
ı
ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ ВЕЛИКОБРИТАНИЯ
(RU)
44 Ferm
