764213
5
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
5
EN
Wear a dust mask
Switch off the machine immediately in case of:
Malfunction in the mains plug, power cable or
damaging of cable.
Broken switch.
Smoke or stench of scorched insulation.
Wait for the cutter to stop before setting
the tool down. An exposed cutter may
engage the surface leading to possible
loss of control and serious injury.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double
insulated; therefore no earthed wire is
required.
When replacing old cables or plugs
Throw away old cables or plugs immediately
as soon as new ones have replaced these. It is
dangerous to put the plug of a loose cable into the
socket outlet. When using extension cables Only
use an approved extension cable that is suitable
for the machine’s power. The cores must have a
diameter of at least 1.5 mm2. When the extension
cable is on a reel, unroll the cable in its entirety.
3. OPERATION
Before setting up, repair or maintenance
of the appliance you must always turn off
the operating switch and pull out the
mains plug!
Before initial operation
Check if the rated voltage and rated frequency
of the mains supply correspond to the details
of the type plate.
Place the workbench on a stable and even
base.
Operation
Fig. 1
To adjust the planing depth, turn the control
knob (1) in a clockwise direction. On the
control knob there is a pointer which shows
the planing depth in mm. Turn the control knob
until the desired planing depth is shown.
Never alter the planing depth during an
operating cycle, otherwise this will result
in an uneven surface. To prevent
operating errors turn the control knob
back to “0” when planing is completed.
Secure the work piece with clamps or similar.
Place the front sole on the edge of the work
piece in such a way that the planing tool does
not yet touch the work piece. The work piece
must be level.
Switching on and off
Fig. A
Switch the machine on by pressing the On/Off
switch (3). When you release the On/Off switch
(3) the machine will turn off.
Lock-on Button
Fig. A
You can lock the On/Off switch (3) by pressing
the On/Off switch (3) and then pressing the
lock-on button (4).
To release the switch-lock; shortly press the
On/Off switch (3) again’
The planer is now switched on and you can let
go of the release button.
Always hold the planer with both hands on
the handles, so as to gain the best possible
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm PPM1015P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm PPM1015P in de taal/talen: Nederlands, Engels, Frans, Turks als bijlage per email.

De handleiding is 4,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info