763928
5
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
5
EN
Removing
Place the chuck key (10) into one of the holes
in the chuck (1).
Open the chuck (1) by turning the chuck key
(10) counterclockwise.
Remove the drill bit (11) from the chuck (1).
Close the chuck (1) by turning the chuck key
(10) clockwise.
Remove the chuck key (10) from the chuck (1).
Setting depth stop
Fig. C
Insert the depth stop (3) in the hole in the side
handle ring.
Slide the ruler to the desired depth.
The On/Off switch
Fig. A
Switch the machine on by pressing the On/Off
switch (5). When you release the On/Off switch
(5) the machine will turn off.
The rotation-speed can be adjusted by
pressing the On/Off switch (5) harder for
raising the rotation-speed or release pressure
for lowering the rotation-speed.
Lock-on Button
Fig. A
You can lock the On/Off switch (5) by pressing
the On/Off switch (5) and then pressing the
lock-on button (4).
To release the switch-lock; shortly press the
On/Off switch (5) again.
Adjusting of the maximum rotation speed
Fig. A
Adjust the speed by turning the speed
adjustment wheel (6) to the desired maximum
rotation speed.
Switching the direction of rotation
Fig. A
Do not change the direction of rotation
during use.
Direction of rotation counter-clockwise: shift
left/right rotation switch (7) to “ ”.
Direction of rotation clockwise: shift left/right
rotation switch (7) to “ ”.
Function selection switch
Fig. A
In order to avoid damage to the machine,
adjusting the function selection switch (2)
shall only be done when machine is not
running
Set the function selection switch (2) to
for drilling.
Set the function selection switch (2) to
for hammer drilling.
Gear selection switch
Fig. A
In order to avoid damage to the machine,
adjusting the gear selection switch (8)
shall only be done when machine is not
running.
If you set the gear selection switch (8) to
position “1”, the drilling speed can be adjusted
between 0 and 1,000 /min.
If you set the gear selection switch (8) to
position “2”, the drilling speed can be adjusted
between 0 and 2,800 /min.
When the gear selection switch (8) cannot
switch easily between “1” and “2”, give the
chuck (1) a little spin by using your hands. This
will help the gears fall into the correct position
and makes switching the gears easier.
User tips
Always use the machine with the side handle
firmly anchored in place - you will not only work
with more comfort, you will also work with more
precision.
Caution: drilling bits and hammer drilling
bits can get very hot
Drilling and hammer drilling
For large holes, for instance in very hard
concrete, start using a smaller bit for pilot
drilling first , then drill to nominal size.
Hold the machine firmly with 2 hands. Be
aware the drill can jam and because of that
machine might suddenly turn (Especially when
drilling deep holes).
Do not apply a lot of pressure on the machine,
let the machine do the work.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm PDM1045P-A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm PDM1045P-A in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 3,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info