510117
11
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
EN
11
Ferm
• Hold the handgrip (2) firmly and move the
turntable to the left or right. The entire saw
moves in the direction required.
• Then screw the two screws tight again.
• The turntable clicks into place at the following
angles: 0º, 15º, 22,5º, 30º, and 45º (both left
and right).
b. Table Saw
See: Parallel and mitre guide (table saw)
Set the guide for mitre sawing and follow the
procedure under ‘Using the table saw’.
Bevelling
(Mitre saw/table saw)
When bevelling the piece of work is sawn at an
angle to the vertical.
The bevel angle is a maximum of 45º.
• Unscrew the knob (6).
• Set the required bevel angle using the scale
(7).
• Screw the knob tight again.
Double mitring (mitre saw)
When double mitring the piece of work is placed
against the stop and sawed across its breadth in
both mitring and bevelling cutting directions.
• Set the mitring angle.
• Set the bevelling angle.
• Follow the procedure under ‘Using the mitre
saw’.
Note: With double mitring the saw blade
is more exposed because of the large
angle. So there is a greater chance of
injury. Keep your hands a good distance
from the saw blade!
Problems
The motor does not start
• The plug is not in the socket
• The power cord is broken
• The switch is defective. Take the machine to
your Ferm dealer for repair.
The fuse is burnt out:
• Remove the plug from the socket.
• Remove the cap (nr. 31 on Fig.1) from the fuse
box with help of a screwdriver
• Check the fuse and replace when necessary.
Always replace the fuse by a new one with the
same specification.
• Mount the cap on the fuse box again.
The saw cut is not even (jagged)
• The saw blade must be sharpened
• The saw blade is mounted back to front
The saw blade is clogged with resin or
sawdust
• The saw blade is not suitable for the piece of
work being used
The motor has difficulty in reaching full speed
• The extension cable is too thin and/or too long
• The mains voltage is less than 230 V.
The machine vibrates excessively
• The saw blade is damaged
• The machine is not fixed to the workbench
The machine becomes excessively hot
• The ventilation slots are blocked. Clean them
out with a dry cloth.
5. Service and maintenance
Maintenance
Always make sure that the machine is not
connected to the mains electricity when
you carry out any maintenance of the
mechanism.
Ferm machines are designed to function for a long
time without any problems with a minimum of
maintenance. By cleaning the machine regularly
and using it in the correct way you can contribute
to a long life of your machine.
Transport
• Check that all locks and tensioning devices
are secure.
• Carry the machine with both hands under the
lower bench surface when the machine must
be moved.
Cleaning
Clean the machine housing regularly with a soft
cloth, preferably after each time you use the
machine. Make sure that the ventilation slots are
free of dust and dirt. For stubborn dirt use a soft
cloth dampened with soapy water. Never use
solvents such as benzene, alcohol, ammonia, etc.
These types of solvents can damage the plastic
parts.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-MSM1033

Zoeken resetten

  • De zaag is te zwaar belast en daardoor is de zekering doorgebrand. Waar kan ik vinden welk type zekering ik moet hebben en waar ik die kan verkrijgen?
    Gesteld op 16-1-2021 om 22:30

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm MSM1033 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm MSM1033 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info