510087
6
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
EN
6 Ferm
the chuck (4).
• Turn the auxiliary grip (7) to the required
position.
• Tighten the auxiliary grip (7) by turning it
clockwise.
Removing
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Remove the auxiliary grip (7).
• Tighten the auxiliary grip (7) by turning it
clockwise.
Mounting and removing the depth stop
(fig. C)
Mounting
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Insert the depth stop (8) through the hole in
the auxiliary grip (7).
• Set the depth stop (8) to the required position.
• Tighten the auxiliary grip (7) by turning it
clockwise.
Removing
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Remove the depth stop (8).
• Tighten the auxiliary grip (7) by turning it
clockwise.
Mounting and removing the dust collector
(fig. D)
The dust collector prevents dust from entering the
machine when drilling into ceilings.
Immediately replace a damaged dust
collector.
Mounting
• If necessary, remove the accessory from the
chuck (4).
• Slide the dust collector (15) over the shaft of
the accessory.
• Insert the accessory with the dust collector
(15) into the chuck (4).
Removing
• Remove the accessory with the dust collector
(15) from the chuck (4).
• Remove the dust collector (15) from the
accessory.
Use
Switching on and off
(fig. A)
• To switch on the machine, press the on/off
switch (1).
• To switch off the machine, release the on/off
switch (1).
Setting the operating mode
(fig. A & E)
The drill selection switch and the hammer
selection lever must be set according to the
required operating mode. Refer to the table below
to set the required operating mode.
Setting (fig. E) Operating mode
A Demolition hammer / Chisel
B Hammer drill
C Drill
• Turn the drill selection switch (2) and the
hammer selection lever (3) to the required
position.
Speed Preselection
The required speed can be preselected with the
thumbwheel. Also during running the rotational
speed can be adjusted.
1 – 2 = low speed
3 – 4 = medium speed
5 – 6 = high speed
Max = maximum speed
The required speeds depends on the material and
can be determined by practical testing.
Hints for optimum use
• Clamp the workpiece. Use a clamping device
for small workpieces.
• Firmly hold the machine by the grip.
• Set the operating mode.
• Switch on the machine.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm HDM1021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm HDM1021 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info