632738
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
EN
water to run on to unwashed surfaces.
Shutting down the pressure washer
The use of detergents can dramatically reduce
cleaning time and assist in the removal of difficult
stains. Some detergents have been customized
for pressure washer use on specific cleaning
tasks. These detergents are approximately as
thick as water. The use of thicker detergents,
such as dish soap, will clog the chemical
injection system and prevent the application of
the detergent. The cleaning power of detergents
comes from applying them to a surface and
giving the chemicals time to break down the dirt
and grime. Detergents work best when applied
at low pressure. The combination of chemical
action and high pressure rinsing is very effective.
On vertical surfaces, apply the detergent starting
at the bottom and work your way upward. This
will prevent the detergent from sliding down and
causing streaks. High pressure rinsing should also
progress from the bottom to top. On particularly
tough stains, it may be necessary to use a brush
in combination with detergents and high pressure
rinsing.
CAUTION! Never disconnect the high-
pressure hose from the machine while
the system is still pressurized.
Follow the correct procedure:
1. Turn off the pressure washer by using the
switch on the machine.
2. Unplug the unit from the power source.
3. Turn off the water supply at the tap.
4. Press the trigger of the gun to depressurize the
system.
5. Disconnect the supply hose to the machine
6. Wipe all surfaces of the unit with a damp clean
cloth.
7. Engage the safety lock.
5. SERVICE & MAINTENANCE
Warning! Unplug the electric cable
(power source) prior to any maintenance
or preparatory storage operations.
Make sure that the machine is not live when
carrying out maintenance work on the motor.
To ensure good performance, check and clean
the suction and detergent filters after every 50
hours of operation.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
1. When switched on, the machine will not
start working.
Plug is not well connected or electric socket is
faulty.
Check plug, socket and fuse.
The mains voltage is lower than the minimum
requirement for start up.
Check that the mains voltage is adequate.
The pump is stuck.
Refer to after storage instructions. Switch
off the unit and let the motor cool.
Thermal safety has tripped.
Leave the lance open with water coming
through.
2. Fluctuating pressure
Pump sucking air
Check that hoses and connections are
airtight
Valves dirty, worn out or stuck. Pump seals worn.
Clean and replace or refer to dealer.
3. Water leaking from the pump
Seals worn out
Check and replace, or refer to dealer
4. The motor stops suddenly
Thermal safety switch has tripped due to
overheating.
Check that the mains voltage corresponds
to specifications. An extension cable,
which is too thin, and tool long can cause
a voltage drop and cause the motor to
overheat. Leave to cool down. Use heavy
duty extension cables.
5. The pump does not reach the necessary
pressure.
Water inlet, filter is clogged
Clean the water inlet filter
Pump sucking air from connections or hoses
Check that all supply connections are tight
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm GRM1013 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm GRM1013 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info