462374
11
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
EN
11
the saw blade saws through the piece of work
and passes through the slot in the table. Do
not put any pressure on the saw. Give the
machine time to saw through the piece of
work.
Bring the machine gently up again and switch •
it off by letting go of the switch (1).
Using the slide-function
Fig. 1
The machine must be firmly bolted to a
workbench.
Use the slide-function for sawing wide
workpieces:
Fix the piece of work in place using the clamp•
Screw up the knob (10) a half turn •
anticlockwise.
Slide the machine completely towards •
yourself
Turn on the machine using the switch•
Bring the saw slowly downwards so the saw •
blade saws through the piece of work
Push the machine slowly backwards (in •
direction of guide fence)
Bring the machine gently up again and switch •
it off by letting go of the switch
Using the laser
Fig. 2
To switch on the laser , press the on/off switch •
2.
To switch off the laser , release the •
on/off switch 2.
5. Service and maintenance
Always make sure that the machine is
not connected to the mains electricity
when you carry out any maintenance of
the mechanism.
Slide rails
Dirt can damage the slide rails and thereupon the
operating of the machine.
Clean the slide rails regularly with a soft cloth.•
Drip some lubricating oil on the slide rails•
Move the mitre saw forwards and backwards •
so the oil spreads over the complete rails
These machines are designed to function for a
long time without any problems with a minimum of
maintenance. By cleaning the machine regularly
and using it in the correct way you can contribute
to a long life of your machine.
Cleaning
Clean the machine housing regularly with a soft
cloth, preferably after each time you use the
machine. Make sure that the ventilation slots are
free of dust and dirt. For stubborn dirt use a soft
cloth dampened with soapy water. Never use
solvents such as benzene, alcohol, ammonia, etc.
These types of solvents can damage the plastic
parts.
Problem solving
1. The motor does not start
The plug is not in the socket•
The power cord is broken•
The switch is defective. Take the machine to •
your dealer for repair.
2. The saw cut is not even (jagged)
The saw blade must be sharpened•
The saw blade is mounted back to front•
The saw blade is clogged with resin or •
sawdust
The saw blade is not suitable for the piece of •
work being used
3. The height and/or mitre lever is obstructed
Chips and/or dust must be removed•
4. The motor has difficulty in reaching full
speed
The extension cord is too thin and/or too long•
The mains voltage is less than 230 V•
5. The machine vibrates excessively
The saw blade is damaged•
6. The machine becomes excessively hot
The ventilation slots are blocked. Clean them •
out with a dry cloth.
7. The electromotor runs unevenly
The carbon brushes are worn out. Replace •
the carbon brushes or consult your dealer.
Lubrication
The machine does not need any extra lubrication.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm FKZ-255RL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm FKZ-255RL in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 10,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info