Ferm 93
RUNDSAV
Tallende i den følgende tekst korresponderer med afbildningerne på side 2 - 4.
Læs denne brugsanvisning godt igennem før maskinen tages i brug. Sørg for
at De kender maskinens funktion og betjening. Vedligehold maskinen i følge
instruktionerne, for at maskinen altid kan fungere optimalt. Bevar denne brug-
sanvisning og den vedlagte dokumentation til maskinen.
Indhold
1. Tekniske specifikationer
2. Sikkerhedsforskrifter
3. Montage og indstillings forskrifter
4. Betjening
5. Vedligeholdelse
1. TEKNISKE SPECIFIKATIONER
Tekniske data
Produktinformation
Fig. A
1. Håndtag
2. Tænd/sluk-kontakt
3. Spændeknap til skæredybde
4. Netledning
5. Sikkerhedsskærm til savklinge
6. Sekskantskrue
7. Bundplade
8. Stopring
9. Savklinge
10. Kløveanlægsflade
Spænding 230 V~
Frekvens 50 Hz
Optaget effekt 1200 W
Omdrejninger, ubelastet 5000/min.
Savklinge ∅185 x ∅20 x 2.4 mm
Tænder Z24
Maksimal savdybde 90° 65 mm
Maksimal savdybde 45° 43 mm
IP-klasse IP20
Vægt 4.05 kg
Lpa (lydtryk) 92.3 dB(A)
Lwa (lydeffekt) 103.3 dB(A)
Vibrationsværdi 4.689 m/s2
DK
D
NL
F
E
P
I
S
SF
N
DK
12 Ferm
Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water. Never use sol-
vents such as petrol, alcohol, ammonia water, etc. These solvents may damage the
plastic parts.
Replacing hte carbon brushes
Fig. F
• Remove the screws (17).
• Withdraw the carbon brushes (18) from the circular handsaw and inspect them for
wear.
• Place the carbon brushes back in the brush holders provided.
• Check that the copper contact on the carbon brushes makes good contact with the
copper part in the brush holder.
• Replace the screws (17) and tighten them firmly.
Frequent use will cause the carbon brushes to wear down. Regular inspection,
after every 30 hours of use, is essential. If the brushes have worn down to less
than 4 mm, replace.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find an exploded view showing the parts
that can be ordered.
• The tool does not work
when switched on.
• When cutting it is very
difficult to move the
work forward in a
straight line and the cut
is not clean.
• The circular saw
makes a lot of noise
and/or does not run
smoothly.
• Damaged cord and/or
plug.
• Defective switch.
• The blade is bent or
blunt.
• The carbon brushes
are worn.
• Check cord and/or
plug.
• Please contact the
service address on the
warranty card.
• Replace the blade.
• Please contact the
service address on the
warranty card.
GB
D
NL
F
E
P
I
S
SF
N
DK
