MAINTAIN TOOLS WITH CARE
Keep the tool clean for better and safer performance.
Store the discs properly in accordance with the maker’s
instructions.
Follow instructions for changing accessories. Inspect
tool and extension cables periodically and if damaged,
have them repaired by a qualified person or authorised
service body. Keep handles free from oil or grease. Keep
the ventilation slots clean to prevent motor overheating.
Check for damaged parts
Do not use a tool with damaged parts, before further use
a damaged tool must be carefully checked by a qualified
person to determine that it will operate properly. Check
for alignment of moving parts, binding or breakage of
parts, mounting and other conditions that may affect its
operation.
A damaged part or guard should be properly repaired by
an authorised service centre, unless indicated otherwise
in the instruction manual. Have defective switches
replaced by an authorised service centre. Do not use a
tool if the switch does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
ELECTRICAL INFORMATION
This product is complete with a pre-wired mains plug, If
the plug needs replacing follow these instructions.
Wire correctly
The wires in the mains lead are coloured in the following
way:
BLUE • Neutral
BROWN • Live
GREEN/YELLOW • Earth
Securing wires
Secure wires carefully and firmly to the correct termi-
nals. Secure the mains cable in the plug cord grip firmly
Fit a 13-amp fuse. If a 13amp (BS1363) plug is used a (BS
1362) ASTA approved 13-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of
electric shock
ENVIROMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life, please
recycle where facilities exist. Phone the Helpline for cur-
rent advice on recycling.
Helpline
For any questions relating to operational or safety
matters contact:
Ferm Customer Helpline on: 0115 966 1199
Monday-Friday 8am – 6pm
Saturday 9am – 1 pm
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
IEC61F/125/CDV/06.95, EN61029-1
EN55014-1, EN55014-2, EN61000-3-2,
EN61000-2-3
in accordance with the regulations:
98/37/EEC
73/23/EEC
89/336/EEC
from 26-05-1998
GENEMUIDEN NL
W. Kamphof
Quality department
CE
ı
DECLARATION OF CONFORMITY (UK)
6Ferm
Use the right tool
Do not force small tools or attachments to do the job of a
heavy-duty tool. Do not use tools for purposes for
which they were not intended; for example do not use a
circular saw for cutting trees or logs.
Do not abuse the cable
Never carry the tool by the cable or pull it to disconnect
it from the power socket. Keep the cable away from heat,
oil and sharp edges. Do not touch the metal plug pins
when connecting or removing the plug.
Secure work
Use clamps or a vice to hold work. It is safer than using
your hand and it frees both hands to operate the tool. Be
aware that this saw is a powerful machine; you must not
hold the workpiece with hand or foot.
Do not over-reach
Keep a proper footing and balance at all times.
Disconnect tools from power supply
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
Always switch off and unplug the saw from the
power supply before making adjustments or chan-
ging discs.
Remove adjusting keys and wrenches
Ensure that they are removed from the tool before swit-
ching on.
Avoid unintentional starting
Do not carry plugged in tools with your finger on the
switch. Check that the switch is off before plugging in to
socket.
Do not use in rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust or fume
extraction system, make sure it is connected and used.
Extension cables
Use only three core earthed extension cables suitable
for the power input of the tool (minimum cable size
1.5mm2). Plug into an earthed socket only.
When using a cable reel unwind it fully. Do not use long
extension cables.
Outdoors use
If the tool is suitable to be used outdoors, only use an
extension cable intended for outdoor use and marked
accordingly. Use a RCD (residual current device) to pro-
vide protection against electrical shock. Do not use in
rain or damp conditions.
Use recommended accessories
The use of any other accessory or attachment other than
recommended in the instructions or catalogue may pre-
sent a risk of personal injury. Use extension cables suita-
ble for the power input of the grinder (minimum cable
size 1.5mm2). When using a cable reel unwind it fully.
BEFORE USING THE CUT OFF SAW
This saw is for cutting steel and concrete/brick sec-
tions. Use fibre reinforced cutting discs only. Do not
fit a saw blade to this saw.
Do not use on wood or wood derived material.
Check package contents
Check contents against list in this manual to make sure
each item is present.
Check for damage
Before using this item check each part listed is undama-
ged.
Save packaging
Save major packaging for return of product for service or
repair.
Fully assemble
Ensure each item is fully and correctly assembled before
use.
THE SAFETY CHAIN
Ensure the saw is unplugged from mains.
The saw is fitted with a safety chain, which locks the head
down for storage or transportation.
To release the saw head
•Push down on the handle and remove the chain link
from the pin (just behind the motor).
To lock the saw head down
•Push down on the handle and put the link nearest the
pin onto it.
•Check that the link is engaged in the groove in the pin
and it is secure.
ATTACHING THE CLAMP KNOB
Ensure the saw is unplugged from mains.
•Screw the clamp knob clockwise into the threaded
hole on the end of the clamp bar. Tighten with a suita-
ble cross head screwdriver (not supplied).
•Check that it is firmly attached and cannot loosen
unexpectedly.
TO INSTALL OR REMOVE A CUTTING DISC
Ensure the saw is unplugged from mains and the
disc has stopped rotating.
Refer to illustrations below.
Check the new disc is the correct type and diameter and
does not touch the edge of the guard.
Ferm 3
