632675
9
Verklein
Vergroot
Pagina terug
1/156
Pagina verder
9
EN
sleeve (8) with your other hand in clockwise
direction until it is opened far enough for the
bit to slide in.
 Insert the shaft of the drill or screwdriver bit
 Tighten the drill chuck again by firmly rotating
the chuck sleeve (8) counterclockwise.
 Check if the bit is centered well by shortly
activating the machine´s on/off switch.
Adjusting the gears
Fig. F
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between
both positions, this will damage your
machine
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (9) forward or
backwards. The number on the gear switch (9)
shows which position is chosen.
 Position 1: For slow drilling, large drilling
diameter or screw driving. The machine has
high power at a low speed.
 Position 2: For fast drilling or small drilling
diameter
Adjusting the direction of rotation
Fig. G
 Set the direction switch (10) to position “” in
order to drive screws or to use it for drilling.
 Set the direction switch (10) to position “” in
order to remove screws
Switching the machine on and off
Fig. G
The on/off switch (11) is used for activating the
machine and adjusting rotation speed.
 Pressing the on/off switch (11) will activate
the machine, the further the switch is being
pushed, the faster the drill will turn.
 Releasing the on/off switch (11) will stop the
machine.
 Move the direction reversing switch (10) to the
middle position to lock the movement of the
on/off switch. It cannot be activated in this
position.
Only lay down the machine when it has
stopped running completely. Do not
place it on a dusty surface as particles of
dust could get into the mechanism.
Adjusting the torque
Fig. G
The machine has 23 different torque settings
and a special drill mode to set the power being
transmitted to the chuck.
By rotating the torque adjustment ring (12),
screws can be driven to a predetermined depth,
which is ideal for repetitive work. The higher the
number, the more torque will be transmitted.
 Select a low setting for small screws or soft
work material.
 Select a high setting for large screws, hard
work materials and when removing screws.
 You should preferably choose a setting as
low as possible when driving screws. Select
a higher setting if the motor slips before the
screw is fully tightened.
 For drilling, turn the torque adjustment ring
(12) to the setting for drilling by fully turning it
counterclockwise.
Ensure that the direction switch (10) is
always set to during drilling.
The machine is equipped with electronic
overload protection function. When the
machine gets overloaded it will shut
down automatically. When this happens,
please wait for at least 5 seconds to let
the overload protection reset itself.
Work light (13)
Fig. A
The machine is equipped with a work light to
illuminate the work location.
 It automatically switches on when the on/off
switch is being pressed.
 It automatically switches off when the on/off
switch is released again.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CDM1113S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CDM1113S in de taal/talen: Alle talen als bijlage per email.

De handleiding is 22,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info