510091
8
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
GB
8
Ferm
position ‘± in order to remove screws.
Drilling
• Rotate the torque adjustment ring (5) to the
drilling position.
Ensure that the direction reversing
switch (1) is always set to ‘’ during
drilling.
Switching the device on and off
Fig. A
• Depress the on/off switch (4). It regulates the
speed of the appliance by transmitting power
to the switch.
• Release the on/off switch (4) to halt the drill
chuck immediately, it will no longer run on.
• Move the direction reversing switch (1) to the
centre in order to lock the appliance in its
disabled state.
Only lay down the appliance when it has stopped
running completely. Do not place it on a dusty
surface as particles of dust could get into the
mechanism.
Spirit level
Fig. H
The drill is equipped with a dual reading horizontal/
vertical level to assist in keeping the drill “level”
while drilling horizontal and vertical holes. The
horizontal level (13) is located in the top of the drill
housing. The vertical level (14) is located on the
rear of the drill housing.
To maintain a level drilling position, hold the drill
where the level bubble is centred in the level
indicator circle.
Charging the battery
• The included battery is delivered in partly
charged condition.
• Only use the battery charger in a temperature
range between + 5 °C to + 40 ºC.
• Only use the battery charger in dry, ventilated
rooms.
Charging
Fig. F
One advantage of using Lithium-Ion batteries is
that, until the battery is almost empty, hardly any
power fading is noticeable. The machine can be
used until you start noticing that the power of the
drill is elapsed. The battery is discharged now and
needs to be charged.
Charging the battery
Fig. F
• Place the battery stem (9) into the matching
cavity on top of the charger (10).
• Make sure the battery stem is pressed fully
into the charger as far as it will go.
• Plug the charger into the electrical outlet.
LED indicators
Fig. G
When the battery charger is plugged in and the
battery inserted, the battery charger will begin
charging the battery. The red LED (11) and the
green LED (12) on top of the charger will indicate
the charging status.
• When the charger is plugged in without a
battery inserted, the green LED (12) will be lit
up.
• When a battery is inserted, the red LED (11)
will start blinking, indicating charging has
started.
• When the battery is full, charging will stop and
the green LED (12) will start blinking.
• If the battery is left in the charger, the charger
will go on standby after 2 hours. The green
LED (12) will stop blinking and light up.
When an error occurs the red LED (11)
will be lit up.
If the temperature of the battery is too
high to get charged safely, both the
green LED (12) and red LED (11) will be
lit, indicating charging process is on
hold. Charging will start when the
battery has cooled down.
Lithium-Ion cells can be stored for a
long period without losing much of their
charge. When the machine is not being
used over a longer period of time, it is
best to store the battery in charged
condition.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CDM1086 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CDM1086 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 13,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info