Ferm 07
• Only use the battery charger in dry, ventilated
rooms.
Charging
Fig. E
• Place the battery holder on a flat table and
put the battery in the battery holder. Pay
attention to + and - pole markings.
• Put the adapter plug of the net adapter in the
connector on the side of the battery holder.
• Put the net adapter in the socket.
• The red charging lamp on the battery holder will
illuminate indicating the battery is being charged.
• The charging process of a fully discharged
battery will take approximately 5 hours the first
time and afterwards approximately 3 hours.
After the charging time the red light will
not switch off automatically! Remove
the battery within 5 hours from the
charger. If the battery is not removed
from the charger after the charging
period it may become overheated.
Discharging the battery
Not only charging batteries is important,
discharging is of equal importance or
even greater importance.
• When the battery is charged the cordless drill
has to be used until you start noticing that the
power of the drill is diminishing and that the
maximum rotational speed is not reached.
• The battery is almost discharged now. Only
now you can start charging the battery.
• Charging the battery while it is still charged for
say one-third of capacity, the so-called
‘memory effect’ can occur. Since during
charging only the discharged part of the
battery capacity of the battery is being
charged now, the battery can start crystallizing
in the one-third that is still charged. This part
of the battery capacity can never be used
afterwards.
• Do not discharge the battery to the minimum.
As soon as you notice that the power or the
maximum rotational speed is diminishing, you
have to charge the battery. When you proceed
using the drill and the battery becomes fully
discharged, the so-called ‘switch of poles
effect’ can occur. The polarity of the battery
poles will be switched: the ‘+’will become ‘-‘
and the ‘-‘ will become the ‘+’.
Once this has occurred the polarity will remain
switched during loading and this will damage
the battery irreparable.
When the cordless drill is not being
used over a longer period of time, the
battery has to be charged fully first. The
battery has to be stored in charged
condition.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Cleaning
Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
Regularly clean the machine housing with a soft
cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth
moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc.
These solvents may damage the plastic parts.
Lubrication
The machine requiers no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part,
please contact the service address on the
warranty card. In the back of this manual you find
an exploded view showing the parts that can be
ordered.
Environment
To prevent damage during transport, the
appliance is delivered in a solid packaging which
consists largely of reusable material. Therefore
please make use of options for recycling the
packaging. NiCd cells are recyclable.
GB
50 Ferm
3. MONTAGE AF TILBEHØR
Fjern altid batteriet inden du begynder
på arbejdet.
Isætning og udtagning af bor
Fig. B
Foruden bor kan man sætte skruetrækkerbits
med sekskantet skaft i maskinen
• Løsn borepatronen (4) ved at dreje på flangen
(9).
• Sæt borets skaft ind i åbningen i
borepatronen.
• Spænd borepatronen så boret sidder godt
fast.
• Løsn borepatronen igen når du vil udskifte
boret.
Isætning og udtagning af batteriet
Fig. C
Kontroller at den udvendige overflade
på batteriet eller værktøjet er ren og tør,
inden du tilslutter opladeren.
• Sørg for at knappen til omløbsretningen (6 på
fig. A) står i den midterste position, for at
undgå utilsigtet start af maskinen.
• Sæt batteriet (5) ind i maskinens sokkel som
vist på tegningen. Tryk det helt i bund så det
går i hak.
• For at fjerne batteriet skal du trykke
låsekapperne (10) på begge sider ind og
trække batteriet ud af maskinens sokkel.
4. BETJENING
Overhold altid
sikkerhedshenvisningerne, og følg de
relevante forskrifter.
Hold maskinen ordentligt fast, og tryk boret
ensartet ind i emnet. Undgå at overbelaste
maskinen. Anvend udelukkende bor som ikke
udviser synligt slid. Slidte bor har en negativ
indflydelse på maskinens funktionsevne.
Indstilling af drejningsmoment
Fig. D
Maskinen har 16 forskellige indstillinger for
drejningsmoment til regulering af den kraft
hvormed skruer bliver skruet i eller ud.
• Sæt indstillingsringen for drejningsmoment (3)
i den ønskede position.
De indstillinger af drejningsmomentet der er til
rådighed, vises på indstillingsringen dels med
cifrene fra 1 til 8, dels med prikker mellem
cifrene som angiver mellempositioner (dvs. i
alt 16).
• Man skal helst vælge den laveste position der
giver tilstrækkelig kraft til at dreje skruen
rundt. Vælg en højere position hvis motoren
"glider i koblingen".
Anvendelse som skruetrækker.
• Sæt knappen for omløbsretningen (6) i
position 'R' for at skrue skruer i.
• Sæt knappen for omløbsretningen (6) i
position 'L' for at skrue skruer ud.
Boring
• Drej indstillingsringen for drejningsmoment (3)
i boreposition.
Sørg for at knappen for
omløbsretningen (6) altid står i position
'R' når du borer.
Start og stop
Fig. A
• Tryk på startknappen (1). Du kan regulere
maskinens omdrejningstal ved at trykke mere
eller mindre hårdt på knappen.
• Når du slipper startknappen (1), bliver
patronen straks bremset, og der er ikke noget
efterløb.
• Når maskinen er slukket, kan du blokere den
ved at sætte knappen for omløbsretningen (6)
i den midterste position.
Læg først maskinen fra dig når motoren står helt
stille. Læg ikke maskinen på et støvet underlag.
Der kan trænge støv ind i mekanismen.
Opladning af batterier
Det vedlagte batteri er ikke opladet ved
leveringen.
• Brug kun batteriopladeren ved temperaturer
mellem +10 ºC. og + 40 ºC.
DK
