• Do not use the machine for grinding workpieces with
a maximum thickness exceeding the maximum
grinding depth of the grinding disc.
• Do not use grinding discs for deburring.
• When grinding discs have to be mounted on the
thread of the spindle, make sure that the spindle has
sufficient thread. Make sure that the spindle is
sufficiently protected and does not touch the
grinding surface.
• Before use, inspect the grinding disc for any damage.
Do not use grinding discs which are crack-ed, ripped
or otherwise damaged.
• Before use, let the machine run idle for 30 seconds.
Immediately switch off the machine in case of
abnormal vibrations or occurrence of another
defect. Carefully inspect the machine and grinding
disc before switching the machine on again.
• Make sure that sparks do not put people into danger
or that they contact highly flammable substances.
• Make sure that the workpiece is sufficiently
supported or clamped. Keep your hands away from
the surface to be cut.
• Always wear safety goggles and hearing protection. If
desired or required also use another kind of
protection like for example an apron or helmet.
• Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions.
• Ensure that blotters are used when they are
provided with the bonded abrasive product and
when they are required.
• If a guard is supplied with the tool never use the tool
without such a guard.
• For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
• Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become
nessesary to clear dust, first disconnect the tool
from the mains supply (use non metallic objects) and
avoid damaging internal parts.
• Though poor conditions of the electrical mains,
shortly voltage drops can appear when starting the
equipment. This can influence other equipment (eq.
blinking of a lamp). If the mains-impedance Zmax
<0.348 Ohm, such disturbances are not expected.
(In case of need, you may contact your local supply
authority for further information.
3. ASSEMBLY
Prior to mounting an accessory always unplug
the tool.
MOUNTING THE SIDE-HANDLE
The side handle can be used for both left-hand and right-
hand control.
• Fasten the side handle for left-hand operation on the
right-hand side of the machine.
• Fasten the side handle for right-hand operation on
the left-hand side of the machine.
MOUNTING THE GUARD
Fig.2
Mount the guard before using the machine.
Assembly
• Place the guard (2) on the housing. Be aware that the
notch of the guard falls across the edge of the
housing.
• Place the fixing-ring (7) on the guard: the ring-holes
have to be on the screw-holes.
• Mount the guard en fixing-ring with help of the 4
screws and washers (8).
• The closed side of the guard always has to point in the
user’s direction.
Be aware the screws are tightened well enough.
Check regularly if the screws are still fixed.
Disassembly
• Remove the flange nut and the grinding disc with
lower flange from the spindle.
• Unscrew the 4 screws (with washers) en remove the
fixing-ring.
• Remove the guard from the machine.
MOUNTING A GRINDING DISC
Fig.3
Use grinding discs of the correct dimension. Use fibre
reinforced grinding discs only. The grinding disc must
not touch the edge of the guard.
Remove the plug from the mains
• Press the spindle lock (5) and turn the spindle (6)
until it engages in the lock. Keep the spindle lock
pressed during this procedure.
• Remove the flange nut (10) from the spindle using the
spanner (11).
• Position the grinding disc on the flange (9).
• Place the flange nut on the spindle and tighten it using
the spanner.
• Release the spindle lock and check that the spindle is
unlocked by rotating it.
MOUNTING GRINDING DISCS AND
ROUGHING DISCS
Fig. 4 and 5 show how to mount the flange (10) when
using thick (4 – 8 mm) and thin (2,5 – 4 mm) discs.
4. USE
SPECIAL ATTENTION WHEN STARTING
THE MACHINE
• Clamp the workpiece and make sure that the
workpiece cannot slide from under the machine
during the cutting activities.
• When working with the machine, always hold it
firmly with both hands and provide for a secure
stance.
• Always direct the cable to the rear away from the
machine.
• Insert the mains plug only when the machine is
switched off.
• Apply the machine to the workpiece only when
switched on
4Ferm
Vi erklĺrer under almindeligt ansvar, at dette
FAG-125N
er i overensstemmelse med fŅlgende standarder eller
normative dokumenter:
EN50144-1, EN50144-2-3, EN55014-1,
EN 55014-2, EN61000-3-2, EN61000-3-3
i overenstemmelse med direktivreglerne
98/37/EC, 73/23/EEC, 89/336/EEC,
2002/95/EC, 2002/96/EC
Frå 01-01-2007
ZWOLLE NL
J.A. Bakker - van Ingen J. Lodewijk
CEO Ferm BV Quality Manager
Ferm Global
Vores firmapolitik bygger pĆ lŅbende forbedring af
vores produkter, og vi forbeholder os retten til at ĺndre
produktspecifikationer uden varsel.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle
Holland
CE
ı
KONFORMITETSERKLÆRING (DK)
Ferm 41
