442906
5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
5
POWER RATING
260 WATTS
FUSE
POWER STANDBY
SPEAKER EXT.
SPEAKER
FOOT
PEDAL
A. POWER RATING - Connect the power line cord to a
g rounded AC receptacle in accordance with the
voltage and frequency ratings shown on the Rear Panel
of the amplifier.
B. FUSE - Protects the amplifier from electrical faults.
Replace fuse only with same type and rating listed on
the fuse holder. If the amplifier repeatedly blows fuses,
take the amplifier to an authorized Fender Service
Center.
C . POWER SWITCH - Push UP to switch ON the amplifier.
Push DOWN to switch OFF the amplifier.
D. STANDBY SWITCH - Push DOWN to put the amplifier
into STANDBY mode. Push UP to put the amplifier into
normal OPERATING mode. In STANDBY mode, power
is supplied to the tube filaments only. This eliminates
w a rm-up time when re t u r ning the amplifier to
OPERATING mode and also increases tube life span.
The POWER switch {C} must be ON for the STANDBY
switch to function.
E. MAIN SPEAKER JACK - Plug-in connection for
speakers. A speaker must always be connected at this
jack when the amplifier is ON.
F. EXTERNAL SPEAKER JACK - Plug-in connection for
an external speaker. This jack is wired in parallel with
the MAIN SPEAKER JACK {E}. A total speaker
impedance load of 4-ohms should be used to avoid
damage to the amplifier.
G. FOOTSWITCH JACK - Plug-in connection for the
FOOTSWITCH which enables ON/OFF switching of the
VIBRATO and REVERB effects. The VIBRATO effect
will not function without the FOOTSWITCH plugged in.
TYPE: PR 186
PART NUMBE R : 021-7370-000 (100V, 50/60Hz) Japan, 021-7300-000 (120V, 60Hz) USA, 021-7360-000 (230V, 50Hz) Euro,
021-7340-000 (230V, 50Hz) UK, 021-7330-000 (240V, 50Hz) A u s t r a l i a .
POWER REQUIREMENTS: 260 watts
POWER OUTPUT: 85 watts R.M.S.
IMPEDANCES: INPUTS 1: 1M ohm (both channels), INPUTS 2: 136k ohms (both channels)
OUTPUT: 4 ohms (both speaker jacks together)
FUSE TYPE: 4 ampere, slow-blow, 125 volt minimum
SPEAKER COMPLEMENT: Two 12-inch Fender vintage re-issue Special Design speakers (P/N-037617)
TUBE COMPLEMENT: OUTPUT: Four Fender Special Design 6L6GC’s (P/N-039214),
PRE-AMP: Four Fender Special Design 12AX7As (P/N-013341),
Two Fender Special Design 12AT7’s (P/N-023531)
FEATURES: Vibrato and Reverb, Tilt-back legs
DIMENSIONS: HEIGHT: 19-7/8 in. (49.2 cm)
WIDTH: 26-5/32 in. (63.5 cm)
DEPTH: 10-3/8 in. (21.9 cm)
WEIGHT: 64 lbs. (29 kg)
Product specifications are subject to change without notice.
`65 Twin Reverb – Rear Panel
The tube BALANCE and BIAS of your ‘65 Twin Reverb is adjusted at the factory and should
provide years of service before needing attention. If the sound quality of the amp has degraded
noticeably and HUM BALANCE and BIAS adjustments fail to restore sound quality, the tubes
are worn and need replacement. Note that pre-amplifier tubes last longer than output tubes. If
you are not sure about the condition of your tubes or the following procedures, take your
amplifier to an authorized Fender Service Center.
A. HUM BALANCE ADJUSTMENT - This adjustment minimizes the hum heard at the speakers
due to tube filament imbalance. Balance is usually adjusted only when tubes have been
replaced. •Adjustment Instructions: Turn the amplifier ON for 2 minutes with nothing
plugged into any of the INPUTS. Rotate the VIBRATO CHANNEL volume, middle, and bass
knobs fully clockwise and the treble knob fully counter-clockwise. Rotate ALL of the
NORMALCHANNEL knobs fully counter-clockwise. Switch OFF the REVERB and VIBRATO
effects. Then insert a slotted screwdriver into the BALANCE ADJUSTMENT control, (see
“A” in FIG. 1) and rotate back and forth to the position with the least amount of hum.
B . BIAS ADJUSTMENT - This adjustment only should be made if the output tubes are
replaced with tubes not identical to the original tubes and should be adjusted only by an
authorized Fender Service Center.
Tube Adjustments
Specifications
Replace tubes with identical F e n d e r® original equipment only (see SPECIFICATIONS below). Tube location is printed on the tube label, inside the cabinet.
FIG. 1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fender 65 Twin Reverb bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fender 65 Twin Reverb in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info