500406
5
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
5
See general warranty conditions printed in separate.and drilling ceramics and for starting to drill brick without a
piercer.
High speed (2) (lever forwards) (DCF10/10.8R) for
drilling brick, for drilling wood and derivatives, plastics and
metals.
The speed can be adjusted while the machine is run-ning.
However, this should not be done at full load. If, when the
machine is stopped, the selector C cannot be set in its nal
position, push the on/off E switch briey.
4. Attachment of bits in the keyless drill chuck
1. Open the drill chuck A and insert the drill bit or screwdriver
bit (in clamp H).
2. To block the bit or screwdriver tip, turn the drill chuck in
a clockwise direction, looking at the ma-chine from the front.
5. Torque adjustment
For use as a screwdriver, the drill-screwdriver is equipped
with an adjustable clutch, operated by the torque adjustment
control B which has 15 settings. Once it has been correctly
adjusted, the friction clutch is released when the pre-selected
torque setting is reached, to avoid the screw penetrating too
far or damage to the machine. Adjustment depends on the
type and size of the screw used. It is advisable to always
begin in the lowest setting (1) and increase gradually until the
desired result is obtained.
For use as a drill, set the torque adjustment control B to
the drill setting. The clutch is designed not to work in the drill
mode.
CHARGING THE BATTERY
To remove the battery F from the machine, press both side
buttons, G, situated on the handle, at the same time.
To charge the battery with a quick 45 minute charger, proceed
as follows:
1. Place the battery charger I on a at surface and plug the
charger into the mains.
2. Plug in the charger. the green light on
3. Put the battery in charger. If battery is in good condition,
the red light will be on. If the battery is in poor condition,the
red light will not be on. Please replace the battery.
4. The red light off when the battery is fully charged, ready
for use.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
Remove the battery before carrying out any opera-tion on
the machine.
- Clean the machine very carefully after each use. The air
vents should always be kept clear.
- Store in a dry place, away from cold .
- Use only Felisatti accessories and spares. These should
be tted in a Felisatti technical service centre (See Warranty/
Technical Service Centre address leaet).
- Brush replacement: The brushes disconnect auto-
matically and should be replaced after 80 - 100 hours use
or when they are less than 3 mm long. Have them replaced
by an Ofcial Service Centre. We re-commend that at every
second change of brushes, you take the machine to one of
our Ofcial Service Centres for general cleaning and oiling.
WARRANTY
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Felisatti DCF10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Felisatti DCF10 in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info