502025
15
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
KBM 65 Q / KBM 65 QF
15
EN
Handling.
The chipping protector (13) must
always be mounted to protect the user
from the chippings.
The contact surface for the magnetic foot
must be smooth, clean and rust-free.
Remove any varnish or flat coat.
The core drill is unsuitable for anti-mag-
netic materials.
For guaranteeing the magnetic adhesion
force also for steel materials of less than
12 mm thickness, the work piece should
be reinforced using an additional steel
plate.
Use the correct speed as given in the table.
The coolant pump (l) for assisting the
cooling should always be mounted before
starting any work. As a coolant, a cooling
lubricant of a lighter grade should be used
that can be pumped without clogging the
pump mechanism.
Danger of injury! Danger of an
electric shock
When working on walls and ceilings avoid
any (coolant) fluid penetrating the core
drill.
Recommendation: work without using
any coolant.
For switching ON/OFF.
First check that the cable and plug are
not damaged.
Switch on the main switch (4) to
ensure that the magnet clamps and that
the drill jig is exerting its magnetic
clamping force.
When working on walls and ceilings,
secure the unit with a safety strap (k).
Switch on the drill motor.
The motor only starts running when the
main switch (4) has been switched on
first, followed by the motor switch (9).
The magnetic foot (8) is monitored by a
current sensor. If the magnetic foot (8) is
defective the motor does not run.
If the motor is overloaded, the electronics
automatically switch off. The motor can
be started again by switching the motor
switch (9) OFF and ON again.
If the current feed is interrupted while the
motor is switched on, or the power tool
is plugged in when the motor switch (9) is
switched on, the safety device prevents
the motor from running. For putting into
operation, turn the motor switch (9) OFF
and then ON again.
Setting the speed.
For core-drilling using the “FAST”
speed (9) the recommended gear must be
set using the speed switch (10).
The “SLOW” motor setting (9) reduces
the set speed by approximately one half.
This motor setting is intended for drilling
and rubbing. Halving the electrical speed
causes a reduction in power.
!
3 41 01 018 06 7 - Buch Seite 15 Dienstag, 16. März 2004 7:47 07
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fein KBM 65 Q bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fein KBM 65 Q in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info