Handleiding Falmec Vetra 90 (pagina 26 van 72) (Alle talen)

709763

Verklein

Vergroot

Pagina terug

1/72

Pagina verder

USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g. micro-

wave ovens), which could interfere with the radio control and with the hood

electronics.

The maximum operating distance is 5 metres, that may vary according to the pres-

ence of electromagnetic interferences.

Radio control operated at 433.92MHz.

The radio control consists of two parts:

- the receiver built into the hood;

- the transmitter shown here in the gure.

DESCRIPTION OF TRANSMITTING COMMANDS

Motor switch-on and speed increase from 1

to 4. Speed 4 is only active for a few minutes.

DOWN

Speed decrease and motor switch-oﬀ.

Light ON-OFF

TIMER ON: The motor automatically switches

oﬀ after 15 min.

The function is automatically disabled if the

motor is switched oﬀ (

key)

Command transmission active

ACTIVATION PROCEDURE ( only for Vetra Wall)

Before using the radio control, follow the procedure below on the hood pushbutton panel:

• Press LIGHT (

) and TIMER ( ) simultaneously until all LEDs start ﬂashing.

• Release the two keys and press LIGHT (

) again until all LEDs are lit up.

• Release LIGHT (

): now the receiver is active.

This procedure is also used to deactivate the receiver.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.

With several radio controls in the same room, a new code can be created by following the

procedure below.

Disconnect the power to the hood before starting the procedure.

1  CREATE A NEW CODE

The procedure is to be carried out on the radio control.

• Press LIGHT

and TIMER simultaneously until the display starts ﬂashing.

• Press DOWN

on the radio control: saving is conﬁrmed by three brief ﬂashes of the

display. The new code cancels and replaces the previous default code.

Reconnect the hood to the electrical power supply, making sure that the

lights and motor are o.

2B  ASSOCIATING THE RADIO CONTROL WITH THE HOOD

USING THE ROTARY CONTROL

press LIGHT (

) on the hood pushbutton panel for 2 seconds:

the red LED lights up.

press any key on the radio control within 10 seconds.

2A  ASSOCIATING THE RADIO CONTROL WITH THE HOOD

USING THE ELECTRONIC PUSHBUTTON PANEL

press TIMER (

) on the hood pushbutton panel for 2 seconds:

the red LED lights up.

press any key on the radio control within 10 seconds.

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

• Press UP

and DOWN simultaneously on the radio control for more than 5 sec-

onds: reset is conﬁrmed by three brief ﬂashes of the display.

• Reconnect the hood to the electrical power supply.

• Proceed with associating the hood and the radio control, as described in point 2.

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the

equipment by removing the plug or switching o the main switch.

Do not use detergents containing abrasive, acidic or corrosive substances

or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.

Special attention is to be paid to the metal anti-grease lters : frequent cleaning of the

ﬁlters and their supports ensures that no ﬂammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once every 15 days

prevent oily substances and grease from sticking to them.

Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth,

slightly moistened with mild, liquid detergent or denatured alcohol.

Finish oﬀ cleaning by rinsing well and drying with soft cloths.

Do not use too much water next to the push button control panel and

lighting devices in order to prevent humidity from reaching electronic

parts.

The glass panels can only be cleaned with speciﬁc, non-corrosive or non-abrasive deter-

gents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

It is forbidden to clean electrical parts, or parts related to the motor inside

the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Falmec Vetra 90 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info