500344
47
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
47
INSTALLATION
Check the ap pli ance is electrically safe and gas sound when you have fi nished.
Screw the connector into the cooker inlet until it is fi nger
tight. Using two suitable tools, one on the inlet on the
cooker to make sure it is held steady and one on the
connector, tighten the connector into the inlet on the
cooker.
Minimum torque 15Nm.
Maximum torque 20Nm
Connect the hose to the connector.
In the UK
For Natural Gas the fl exible hose must be in
accordance with B.S.669.
For LP Gas it should be capable of 50mbar
pressure, 70°C temperature rise and carry a red
stripe, band or label.
If in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet in the underside of the connector block on the back of
the cooker.
The hose should be fi tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards
in a ‘U’ shape.
Because the height of the cooker can be adjusted and
each connection is diff erent it is diffi cult to give precise
dimensions. Ideally the house supply connection should be
in the shaded area shown in the fi gure showing the back of
the cooker. (‘B’ in the fi gure)
After completing the gas connection, check the cooker
is gas sound with a pressure test. When checking for gas
leaks do not use washing up liquid - this can corrode. Use a
product specifi cally manufactured for leak detection.
Pressure testing
The gas pressure can be measured at the injector of one
of the centre hotplate burners. Remove the pan support,
burner head and cap. The injector is now accessible.
See Technical data section at the back of this book for test
pressures.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Electrical Connection
This appliance must be installed by a qualifi ed electrician
to comply with the relevant regulations and also the local
electricity supply company requirements.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double pole
switch having a contact separation of at least 3mm in all
poles. This cooker must not be connected to an ordinary
domestic power point.
The total electrical load of the appliance is approximately
5.1kW. The cable size used should be suitable for this load
and comply with all local requirements.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel.
Connect the mains cable to the correct terminals for your
electrical supply type.
Check that the links are correctly fi tted and that the terminal
screws are tight. Secure the mains cable using the cable
clamp.
Current Operated Earth Leakage Breakers
Where the installation is protected by a 30-milliamp
sensitivity residual current device (RCD), the combined
use of your cooker and other domestic appliances may
occasionally cause nuisance tripping. In these instances the
cooker circuit may need to be protected by fi tting a100mA
device. This work should be carried out by a qualifi ed
electrician.
Hotplate
Check each burner in turn. There is a fl ame safety device
that stops the fl ow of gas to the burner if the fl ame goes
out. For each burner, turn the control knob to the large
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Falcon Toledo XT 110 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Falcon Toledo XT 110 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 1,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info