751513
6
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Version 04/08 - Page 6
INSTALL THE RANGEHOOD
1. Remove the unit from the carton and place on a at
surface for assembly. Cover the surface to prevent accidental
damage. Remove all parts including the mounting hardware
before discarding the carton.
2. Remove the grease lters USING TWO HANDS (one to
hold the lter so that it doesn't fall on cooktop and one to turn
the knob) by pulling the knob out and turning to the left.
3. The rangehood is shipped from the factory in the up vent
position as indicated in FIGURE 9. For top vent applications,
no additional adjustments are necessary.
FIGURE 9
For rear vent applications, the blower must be turned inside the
rangehood so that the blower vents to the rear as indicated in
FIGURE 10. The blower is turned by removing two screws on
each side of the blower, rotating the blower with the exhaust
opening facing the rear and then replace the screws. The
exhaust cover must be moved to block the unused opening. The
blower must be converted before installing the rangehood.
FIGURE 11
FIGURE 10
4. Remove the cover from the eld wiring compartment.
Remove the wiring electrical knockout using a at-blade
screwdriver. Feed the Power Supply Cable through the
electrical knockout.
5. The canopy attaches to the wall by two screws discussed
earlier in the installation instructions. The canopy hangs
from these screws by brackets inside the rangehood shown
in FIGURE 11. Before attempting to hang the canopy, you
should rotate the adjustment screw marked V1 in FIGURE
11 counterclockwise to extend the brackets from the
canopy. Using a Phillips head screwdriver, rotate this screw
counterclockwise to extend the bracket.
6. Install the damper before hanging the rangehood. The
damper attaches to the rangehood by two small screws
provided in the hardware package. If 48" hood is to be
connected to 10" round duct, install the Duct Transition Kit
now.
7. Hang the rangehood canopy from the screws. Due to
the weight of the canopy, these screws must be installed into
solid material! Once the canopy is hung, rotate the screw
marked V1 to secure the rangehood to the wall.
MAKE SURE THAT THE RANGEHOOD IS SECURELY
ATTACHED TO THE WALL! FAILURE TO PROPERLY
INSTALL COULD RESULT IN INJURY OR DAMAGE TO
PROPERTY.
8. The brackets shown in FIGURE 11 are also used to
adjust the level of the canopy. Using a Phillips screwdriver,
rotate the screw V2 to adjust the level of the canopy.
9. Connect the Power Supply Cable to the rangehood.
Attach the White lead of the power supply to the White lead
of the rangehood with a twist-on type wire connector. Attach
the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector. Connect the
Green ( Green and Yellow ) ground wire under the Green
grounding screw.
10. Replace the eld wiring compartment cover and the
grease lters.
11. If the installation uses a telescopic chimney, connect the
ductwork and install the chimney. Mount the upper chimney
section to the wall rst. Then mount the lower section. The
lower section ts over the upper section.
If the installation uses a full width duct cover, install it now.
12. Turn the power supply on. Turn on blower and light.
The rangehood controls are located on the right-hand side
under the canopy. If the rangehood does not operate, check
that the circuit breaker is not tripped or the house fuse blown.
If the unit still does not operate, disconnect the power supply
and check that the wiring connections have been made
properly.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Faber Pro Magnum bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Faber Pro Magnum in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info