560682
8
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
7
a
b
c
ENGLISH
4 MANUAL OPERATION
OPEN
CLOSED
UNLOCKED
LOCKED
Fig. 18
5 ELECTRICAL CONNECTION OF THE "2easy bus" ENCODER
The S450H operator is fitted with an encoder system with "2easy bus" technology. The proper assignment of the leaf to the corresponding
encoder depends on the connection of the two encoder wires (leaf 1- encoder 1; leaf 2 - encoder 2).
THE ENCODER WIRES MUST BE CONNECTED TO THE "2easy bus" CONNECTOR OF THE ELECTRONIC EQUIPMENT.
To verify the proper combination LEAF 1 - ENCODER 1 - MOTOR 1 and LEAF 2 - ENCODER 2 - MOTOR 2, refer to the LEDs on the
encoders, as shown by table 2 and the figures 19 - 20 - 21.
To invert the leaf-encoder combination, change the encoder polarity by swapping its wires until the right LEDs are lit.
TABLE 2
LED ON BLINKING OFF
DL 1
Power supply ON and BUS - board
communication
Power supply ON but
no BUS communication
(e.g.: cabling fault)
Power supply OFF and no BUS communi-
cation
(e.g.: missing or broken connection)
DL 2 Encoder associated to leaf 1 / Encoder associated to leaf 2
DL 3
/ Pulse reading during leaf movement Leaf stationary
DL 1: must always be ON to ensure the right connection between encoder and board.
DL 2: indicates the leaf where the encoder is installed.
If the encoder is installed on leaf 1, the DL 2 LED is ON.
If the encoder is installed on leaf 2, the DL 2 LED is OFF.
DL 3:
when blinking at regular intervals, it signals the pulse reading during the leaf
movement. When the gate leaf is stationary, DL 3 is OFF.
If the gate is to be operated manually because of a power failure or an automated system fault, activate the release device.
1) Lift the protection lid (Fig. 18, re.
a) and insert the key in the lock (Fig. 18, ref. b).
2) Turn the key 90° clockwise to open the cover and lift it.
3) Turn the release knob (Fig. 18, re. c
) anticlockwise until it stops.
4) Open or close the leaf manually.
To restore the normal operation of the automated system, perform the above described operations in reverse order.
The LEDs of the encoder remain visible also with the protection cover of the rear
bracket installed.
The models S450H SB are not equipped with a release facility since, thanks to the particular configuration of the hydraulic
distributing flange, you do not need to release the operator to manually move the leaf
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

FAAC-S450H

Zoeken resetten

  • Onze Faac poort installatie opent altijd wel goed maar het sluiten niet. Soms sluit de poort maar 20cm, soms 2m en soms ook volledig dicht. Kan het zijn dat dit aan de fotocel ligt die niet goed meer werkt of dienen we dit probleem te zoeken in de motor of in de sturing. Graag jullie advias aub.

    Mvg Freddy Gesteld op 4-4-2021 om 12:48

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw FAAC S450H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van FAAC S450H in de taal/talen: Engels als bijlage per email.

De handleiding is 1,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van FAAC S450H

FAAC S450H Gebruiksaanwijzing - Nederlands - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info